Bosch TSTBM3H2CPH6W-A Installation Manual download pdf (Page 24)

6 720 220 376

Subject to change without prior notice Revised 02-13

24 TSTBM3H2CPH6W-A Setting 5+1+1 Program

RECOMMENDED HEATING SETTINGS:

Increasing Humidity

The table below shows recommended indoor

humidity levels in relation to outdoor temperatures

during heating (adding humidity).

Outside Temperature

(0°F)

Recommended

Relative Humidity

+20º and above 35% to 40%

+10º 30%

0º 25%

-10º 20%

-20º 15%

RECOMMENDED COOLING SETTINGS:

Consult your professional HVAC technician for

recommended settings for your climate.

SET TIME

1. Press MENU

2. Press SET TIME

3. Day of the week will be ashing. Use the [+] or

[–] key to select the current day of the week.

4 Press NEXT STEP

5. The current hour is ashing. Use the [+] or [–] key to

select the current hour. When using 12-hour time,

make sure the correct a.m. or p.m. choice is selected.

6. Press NEXT STEP

7. Minutes are now ashing. Use the [+] or [–] key

to select current minutes.

8. Press DONE when completed

PROGRAMMING

All programmable Bosch thermostats are shipped with

an energy saving pre-program. You can customize this

default program by following the Set Program Schedule

Instructions below.

Your thermostat can be programmed to have each day

of the week programmed uniquely (7days), all the

weekdays the same with a separate program for

Saturday and a separate program for Sunday (5+1+1),

or nonprogrammable. There are four time periods for

each day (WAKE, LEAVE, RETURN, SLEEP).

This thermostat has a programmable fan feature,

which allows you to run the fan continuously during

any time period.

Set 5+1+1 Program Schedule

To customize your 5+1+1 program schedule, follow

these steps:

Weekday:

1. Select HEAT or COOL using the SYSTEM key.

Caution

You have to program heat and cool each

separately.

2. Press MENU

3. Press SET SCHED.

Caution

Monday-Friday is displayed and the WAKE

icon is shown. You are now programming the

WAKE time period for the weekday setting.

Additional step if TSTBM-RRS--TW-A

indoor remote sensor is connected.

The TSTBM3H2CPH6W-A master thermostat will

either average all sensors (system average) or

only use one sensor for the system ambient

temperature (priority). The default setting is

SYSTEM AVERAGE, which means all sensors are

averaged to create the system average ambient

temperature reading. The NEXT ZONE key can

be pressed to change the priority. The system

information area of the display shows the

priority.

For Example: There is an TSTBM-RRS--TW-A

connected and it is named REMOTE 1. If the

NEXT ZONE key is pressed until REMOTE 1 is

shown, then the REMOTE 1 ambient

temperature reading will be used exclusively for

that time period. All other sensors will be

ignored.

4. Time is ashing. Use the [+] or [–] key to make

your time selection for the weekday WAKE time

period.

Caution

If you want the fan to run continuously during

this time period, select ON with the FAN (3) key.

5. Press NEXT STEP

6. The setpoint temperature is ashing. Use the [+]

or [–] key to make your setpoint selection for the

weekday WAKE time period.

7. Press NEXT STEP

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 30 31 32

Comments to this Manuals

No comments

Bosch TSTBM3H2CPH6W-A Installation Manual Page 24

Comments to this Manuals