1
y Safety instructions
– The washing machine is heavy - lift with caution.
– Frozen hoses can tear/burst. Do not install the washing machine outdoors or in an area exposed
to freezing conditions.
– These installation instructions are intended for use by qualified installers. In addition to these
instructions, if installing the washing machine:
In the United States comply with the National Electric Code, ANSI/NFPA70 - latest edition/State
and municipal and/or local regulations.
In Canada comply with the Canadian Electric Code C22.1 - latest edition/provincial and municipal
and/or local regulations.
– If the washing machine is located in a room which will be exposed to temperatures below freezing,
or if it is located in a cabin that is being shut down for the winter, any residual water in the pump
or water inlet hose(s) must be drained.
– Take care not to damage the washing machine. Do not hold on to protruding parts (e.g. door)
when lifting.
– In addition to the safety information listed here, the local water end electricity supplier may have
special requirements.
– If in doubt, have the appliance connected by an authorized technician.
Proper disposal
– All packaging materials are non-polluting and recyclable. Please contribute to a better environment
by disposing of packaging materials in environmentally friendly manner. Please ask your dealer or
local authority about the best means of disposal.
Old appliances are not worthless rubbish. Valueable raw materials can be reclaimed from
environmentally friendly recycling.
Installation surface
– Stability is important to that the machine does not "walk"!
– The installation surface must be solid and level.
– Soft floors/floor coverings are not suitable.
For installation on a base
– Fasten the washing machine feet with retaining tabs* (*Order no. WMZ 2200, WX 9756).
For installation on a wooden joist floor
– Install the washing machine in a corner if at all possible.
– Screw a waterproof wooden plate (min. 1.18 in. thick) on the floor.
– Fasten the washing machine feet with retaining tabs* (*Order no., see above).
Under-counter/closet installation of the machine
Under-counter / in-cabinet installation before connecting to power supply.
Installation in kitchen cabinets (under-counter or in-cabinet)
– Cubicle width of 23.62 in. is required.
– Only install the washing machine under a continuous counter top which is securely fastened
to the neighboring cabinets.
– If installing the washer in a closet, observe the minimum distances:
Side: 0 in., rear: 1.97 in., top: 0 in., front: 2.76 in.
2
Scope of delivery
Additionally needed depending on connection
– 1 hose clamp Ø 0.94 in.-1.57 in. (commercially available) for connectiong to siphon
a Page 4; Water connection.
Useful tool
– Level for alignment.
Hose and cable lengths
Left-side connection
or
Right-side connection
Note: When using the hose holder, possible hose lengths are reduced!
Available commercially or from customer service:
– Longer supply hose (approx. 86.61 in.), for standard model.
Wrench
Power cord
Water supply hoses
Drainage hose
Elbow
for fixing the waste
water hose
Covers with
hose holders
Standard
55 in.
37 in.
47 in.
51 in.
28 in.41 in.
max. 39 in.
Moisture in the drum is
due to end inspection.
3
Removing shipping locks
– Before first use be sure to completely remove the 4 shipping locks and
keep them.
– All four hose guides need to be installed to prevent access to moving
parts.
– For later shipping be sure to reinstall the shipping locks - prevents
damage to the machine a Page 6.
– Save screws and sleeves.
1. Take the hoses out of the holder and the elbow.
Remove elbow.
2. Loosen and remove all 4 transportation protection devices.
3. Take the power cord out of the holders. Remove sleeves.
4. Fit the covers.
Lock securely by pressing on the locking hook!
5. Fix hoses in the hose holders. Fit the hose clips.
4
Water connection l
– The washing machine must only be operated with cold and hot (max. 140 °F/60°C) tap water. Do
not connect the appliance to the mixer tap of an unpressurized hot-water boiler.
– To prevent water damage, the hot and cold water valves should be accessible when the washing
machine is in place and should always be turned off when the washing machine is not in use!
– If installing the washing machine in a new building or a building in which the plumbing system was
recently installed or upgraded, flush the lines before installing the washing machine to remove any
sand, dirt or residue.
– The connection points are under full water pressure. Check seal with tap fully open.
– To prevent leakage or water damage, follow the instructions in this chapter!
– Do not use a used inlet hose. Only use the inlet hose supplied or one which was purchased from
an authorized dealer.
– If in doubt, have the appliance connected by a technician.
Water supply
Water inlet hose:
Attention: Do not kink, crush, modify or cut through (strength is no longer guaranteed).
Optimum water pressure should be between: 14.5 to 145 p.s.i. (1-10 bar)
– When the tap is turned on, the water flow is at least 2.2 U.S. gallons (8 liters) per minute.
– If the water pressure is higher, install a pressure reducing valve.
1. Connect water supply hoses to the taps.
Tighten plastic screw-fittings by hand only.
2. Carefully turn on the taps and check the connection
points are not leaking.
Attention: screw connection is under water mains
pressure.
Water drainage
Water drainage hose:
Attention: Do not kink or stretch.
Height difference between installation area and outlet:
0 - max. 39 in.
Drainage into a sink/bath tub:
Attention: Secure the drainage hose to prevent it from slipping out of the sink.
Attention: The plug must not be in the plug hole. When the water is being
pumped out of the washing machine, check that the water drains away quickly
enough. Do not insert the end of the drainage hose into the pumped off water!
There is a risk that water will be drawn back into the washing machine!
Drainage into a siphon:
Attention: Secure connection point with hose clip,
Ø 0.9 in. - 1.6 in. (dealer).
.
Drainage into a standpipe or in wall installation:
Use the U-bracket. Attach the U-bracket to the end of the hose and insert end of
hose into standpipe or wall drain. Use a strap or cable tie connected to U-bracket
to hold hose in place.
(34 pages)
(68 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals