Installation ManualMicrowave 500/800 SERIESHMV5053U, HMV8053U
10Adapting microwave blowerThis microwave is shipped assembled for Room Venting Installation. The blower unit is already in place and must not to be a
116.Replace the blower plate and secure with the screws removed in Step 1.7.Attach the exhaust adapter to the rear of the oven by sliding it into the
124.Insert the two remaining self-aligning screws through outer top cabinet holes. Turn two full turns on each screw.5.Tighten center screw completely
13* If a rectangular-to-round transition adapter is used, first make sure the damper hinge of the microwave swings freely. If necessary, cut the dampe
14Testing Operation1.Turn on power at the breaker.2.Test the oven mode:Test the CONVECTION oven mode (if available). See the Use and Care Manual for d
15ContenidoInstrucciones de instalaciónDefiniciones de Seguridad ... 15INSTRUCCIONES DE SEGURIDAD IMPORTANTES
9 INSTRUCCIONES DE SEGURIDAD IMPORTANTESLEA Y CONSERVE ESTAS INSTRUCCIONES16INSTRUCCIONES DE SEG LEA Y CONSERVE ESTAS INSTRUCCIONESINSTALADOR: DEJ
179 INSTRUCCIONES DE SEGURIDAD IMPORTANTESLEA Y CONSERVE ESTAS INSTRUCCIONESservicio técnico en los compartimentos que generan microondas, verifique e
18Lista de verificación de instalaciónUse esta lista de verificación para verificar que haya completado cada paso del proceso de instalación. Esta lis
19Herramientas y piezas necesarias▯ Destornillador con cabeza Phillips▯ Lápiz.▯ Regla o cinta métrica, y borde recto.▯ Taladro.▯ Brocas: 3/16 pulg., 1
2Table of ContentsInstallation instructionsSafety Definitions ... 2IMPORTANT SAFETY INSTRUCTIO
20Requisitos de ubicaciónMedidas para la instalaciónMedidas del aparatoNota: Tome en cuenta que las mediciones delantera y trasera del aparato no son
21Instalación eléctricaEl modelo mencionado en la tapa frontal está diseñado para conectarse a una fuente de alimentación de 120 V CA y 60 Hz. Se util
22Sin pasadores de pared en los orificios de las esquinasSi el pasador de pared se encuentra dentro de 6¼ pulg. (159 mm) de la línea central vertical,
23Acoplamiento de la placa de fijación1.Retire las alas de anclaje de los pernos.2.Inserte los pernos en la placa de fijación a través de los orificio
245.Acople el adaptador del escape a la parte superior de la placa del ventilador deslizándolo en las guías. Empújelo hacia adentro en forma segura ha
255.Corte el orificio de 2 pulg. (51 mm) en “D”. Este orificio es para el cable de alimentación eléctrica.Nota: Si el gabinete es de metal, utilice e
267.Colocar los filtros antigrasa insertándolos en las ranuras laterales y, a continuación, empujando hacia arriba y hacia el horno para bloquearlos (
27* Si se utiliza un adaptador de transición de rectangular a redonda, primero asegúrese de que la bisagra del regulador del microondas se mueva con l
28Prueba del funcionamiento1.Encienda la alimentación eléctrica desde el disyuntor.2.Pruebe el modo del horno:Pruebe el modo del horno CONVECTION (Con
39 IMPORTANT SAFETY INSTRUCTIONSREAD AND SAVE THESE INSTRUCTIONSIMPORTANT SAFETY INS READ AND SAVE THESE INSTRUCTIONSINSTALLER: LEAVE THESE INSTRU
1901 Main Street, Suite 600 • Irvine, CA 92614 • 800-944-2904www.bosch-home.com • © 2016 BSH Home Appliances960301 *9001152495* 9001152495
9 IMPORTANT SAFETY INSTRUCTIONSREAD AND SAVE THESE INSTRUCTIONS4GROUNDING INSTRUCTIONSThis appliance must be grounded. Grounding reduces the risk of e
5Checklist for InstallationUse this checklist to verify that you have completed each step of the installation process. This can help you avoid common
6Parts includedYou will find the installation hardware contained in packet with the unit. Check to make sure you have all these parts:Not shown:▯ Top
7Appliance dimensions Note: Take into account that the front and rear measurements of the appliance are not identical.Power RequirementsThe outlet mu
8Install ApplianceRemoving the mounting plateNote: To avoid possible damage to the work surface or to the bottom of the appliance, cover the work sur
9Attaching the mounting plate to the wallPreparing rear wall9 CAUTIONWear gloves to avoid cutting fingers on sharp edges.Note: Make sure the cabinet
Comments to this Manuals