Bosch INTELLIVOX DDC LBC 325X Installation Manual

INTELLIVOX DDC Installation ManualEN Active Line Array LoudspeakersLBC 325x Series

hexagonal nut. The swivel brackets are mounted tothe rear of the enclosure by four M5 pan headscrews (factory supplied). Refer to Table 4 inchapter 3.

columns can differ substantially from the 2c model.Mechanical drawings of the other models can be foundin chapter 3.5 or in the respected datasheet.Fi

3. Appendix. 3.1 Reference part list. Connectors for external wiring.Table 3 Intellivox external connectors details.Other installation related access

The AGND pin serves as a reference for the SPL andtemperature measuring input circuitry. To keep thisground signal as clean as possible, the AGND wire

Although in terms of safety and immunity this is themost preferable set up, an unwanted ground loop iscreated which can cause audible noise or hum. Th

In order to restore the galvanic safety path of the signalwiring up to a certain level, it is possible to connect a100 OHMS 1W resistor parallel with

Fig 13 Optional high frequency decoupling for 70 V /100 V systems.Conclusion: Because the Intellivox can be a part of a complexinstallation it is impo

Network configuration.A network is composed of one master device and oneor more slave devices. A master device can exist of aPC running the RS-485 net

Master deviceAs mentioned before the RS-485 network conceptneeds one master device. This master device (networkcontroller) is composed of a PC running

Notes for type RS-232 to RS-485 adapter:• Both ends of the RS-232 to RS-485 connector havethe same 9p female sub-d connector. Be careful toinstall it

Disclaimer1. The information in this manual has been carefullychecked for accuracy, but no guarantee is given asto the correctness.2. The information

Fig 17 Wiring configuration using RS-485 networkcable type.Ambient SPL and temperature sensorconnections.Figure 18 and 19 show the wiring configuratio

3.5 Intellivox dimensions of the different models.Fig 20 LBC 3251/00 Intellivox-1b dimensions, all measures in mm.Intellivox DDC | Installation Manual

Fig 21 LBC 3252/00 Intellivox-2b dimensions, all measures in mmIntellivox DDC | Installation Manual | AppendixBosch Security Systems | July 2003 EN|23

Fig 22 LBC 3252/10 Intellivox-2b dimensions, all measures in mmIntellivox DDC | Installation Manual | AppendixBosch Security Systems | July 2003 EN|24

Fig 23 LBC 3253/00 Intellivox-2c dimensions, all measures in mmIntellivox DDC | Installation Manual | AppendixBosch Security Systems | July 2003 EN|25

Fig 24 LBC 3253/10 Intellivox-2c dimensions, all measures in mmIntellivox DDC | Installation Manual | AppendixBosch Security Systems | July 2003 EN|26

Fig 25 LBC 3254/00 Intellivox-4c dimensions, all measures in mm.Intellivox DDC | Installation Manual | AppendixBosch Security Systems | July 2003 EN|2

Fig 26 LBC 3254/10 Intellivox-4c dimensions, all measures in mm.Intellivox DDC | Installation Manual | AppendixBosch Security Systems | July 2003 EN|2

Fig 27 LBC 3256/00 Intellivox-6c dimensions, all measures in mmIntellivox DDC | Installation Manual | AppendixBosch Security Systems | July 2003 EN|29

Fig 28 LBC 3256/10 Intellivox-6c dimensions, all measures in mmIntellivox DDC | Installation Manual | AppendixBosch Security Systems | July 2003 EN|30

Figure and Table lists.Fig 1 LBC 3253/00 Intellivox-2c shown without front grill. . . . . . . . . . . . . . . . . . . . . . . . .5Fig 2 WAGO massive

© 2003 Bosch Security Systems GmbH9922 141 50511enRobert Bosch GmbHGeschäftsbereichPostfach 10 60 5070049 StuttgartTelefax (0711) 811-12 34www.bosch.d

Intellivox DDC | Installation Manual | IntroductionBosch Security Systems | July 2003 EN|51. Introduction.This paper describes the factory recommended

2. Installation guideThis chapter deals with the practical aspects ofinstalling the Intellivox loudspeaker column. • SI units are used as a default, a

A simple surveillance function may be realized bymeans of the ‘failure detect’ connection in case the RS-485 network interface is not used. Three rela

2.3 Wiring and connections.2.3.1 Mains power.• Be sure that the mains voltage stated on the unitcomplies with the local standard before connectingthe

Fig 3 Intellivox connector block.• A removable panel on the front side of theIntellivox (backside for the Intellivox-1b) allows allconnectors to be in

Fig 4 WAGO 231 cross-sectionFig 5 Connecting a WAGO 231Table 2 PVC insert sizes.2.5 Methods for mounting the Intellivox.2.5.1 General.For mounting