High Performance HD LED MonitorUML-463-90 en User Manual
Fax: 65 63521776E-mail: [email protected] ServiceTelephone: 86 (0) 756 7633117 or 86 (0) 756 7633121Fax: 86 (0) 756 7631710E-mail: cust
UnpackingThis equipment should be unpacked and handled with care. If an item appears to have beendamaged in shipment, notify the shipper immediately.V
Access and connections Monitor views1023.68578.27573.271018.68Figure 3.1: Front (with dimensions)111.86158.24Figure 3.2: Side (with dimensions) 400 M6
Rear panel exploded view324567891Figure 3.4: Rear panel exploded viewRef.Button Description1 IR sensor,ambient lightsensor andLEDIndicatorReceives the
4 Increases the value when in theOSD.Increases audio volume.Scrolls right in the OSD.5 Decreases the value when in theOSD.Decreases audio volume.Scrol
Remote control1678910114532Ref. Button Description1 POWERON/OFFTurns power on and off.2 Input Selects a signal source to display.3 Exit Exits the OSD
DescriptionThe Bosch UML-463-90 High Performance LED monitor is a 1080p Full HD resolution colormonitor ideal for use with digital video recorders (DV
Installing the MonitorThis chapter outlines the procedures to install the monitor. A qualified service person shouldinstall the monitor and adhere to
3. Assemble the stands by inserting the stand shaft into the stand foot in the correctdirection using the included screws in the accessory packet.4. A
Note: Both Y and C inputs are terminated with 75 Ohm.Figure 5.3: Y/C Connector pin-outNumber Input1 Ground2 Ground3 Y-signal4 C-signalConnecting Audio
DVI ConnectionConnect to the digital DVI Input connector by using the supplied DVI-D cable.Figure 5.6: DVI InputDisplayPortConnect the PC signal using
133222Figure 5.9: Multiple Monitor ConfigurationRefDescription1 Video Camera2 Video In3 Video OutSee also– Single / Multiple Monitor Configuration, pa
2. The setting page appears:– Information: Shows information of the display. It is for information only. There areno items that can be set.– Picture &
Navigating the MonitorNavigating the Control PanelUse the control panel to make any necessary OSD adjustments. See the figure below for anexplanation
Using the Monitor On-screen Display (OSD)The LCD is programmed through the on-screen display (OSD) menus and submenus where anoperator can select oper
On-screen Display MenusThere are four (4) on-screen menus that allow you to customize your monitor settings. Pressthe MENU button (on Control panel or
Submenu DefinitionPicture Mode Selects the automatic picture control mode. Choices are:Standard: applies factory default values.Vivid: for viewing ver
Sound MenuAccess the Sound menu using the MENU button on control panel or remote control.Figure 6.3: Sound menuSubmenuDefinitionSound mode Adjusts the
Screen MenuAccess the Screen menu using the MENU button on control panel or remote control.Figure 6.4: Screen menuSubmenuDefinitionPAP Setting(Picture
Aspect Sets the picture’s aspect ratio:Wide Zoom: Enlarges to fill screen with minimum distortion.Zoom: Enlarges the picture, keeping the same aspect
Table of contents1Safety 41.1 Important safety instructions 41.2 Safety precautions 51.3 Important notices 51.4 Customer support and services 92Unpack
Adjust screen Auto Adjustment: Auto synchronizes screen to graphics adaptor.Phase: Adjusts the monitor’s phase.Clock Frequency: Adjust the monitor’s c
Setting MenuUse the arrow buttons to make changes and the MENU button to exit submenu.Figure 6.5: Setting menu SubmenuDefinitionLanguage Select a lang
Power Save Sets the display to enter the power saving mode when there is nosignal detected (see also Power Management, page 34).Low: All signal source
Advanced Auto Detection: Automatically detects available input sources.Auto Adjustment: Automatically optimizes image display for the VGAinput.Oversca
Power ManagementThis monitor has a power management system to “power down” upon receipt of the displaypower management signaling (DPMS) from a DPMS vi
TroubleshootingProblem SolutionNo image displayed onscreen– Check that the power cord of the monitor is securelyconnected into the wall outlet or grou
MaintenanceTo clean the LCD panel, wipe off water droplets or oil immediately with absorbent cotton or asoft lint-free cloth. Staining and discolorati
Technical dataElectricalRated Voltage 120/230 VAC, 50/60 HzVoltage Range 100–240 VAC, 50/60 HzFrequency Horizontal: 60–73 KHzVertical: 47–63 HzPower a
VGA (RGB PC) 0.7 Vp-p (0.5–1 Vrms)Audio Input 2.0 V line level, mono RGB and DVI HDMI640 x 480 (60/72/75 Hz) 640 x 480 (60/72/75 Hz)720 x 400 (70 Hz)
Power On/OffControl Panel Lockout Multiple push-button combination On-screen DisplayVideo Mode Input Source, Screen, OSD, Utility Indicators (on rear)
Safety Important safety instructionsRead, follow, and retain for future reference all of the following safety instructions. Heed allwarnings on the un
With Packaging 1190 x 754 x 290 mm(46.85 x 30.08 x 11.42 in.)WeightMonitor Weight 25 kg (55.12 lb)Shipping Weight 30 kg (66.14 lb) EnvironmentalOperat
Bosch Security Systems B.V.Torenallee 495617 BA EindhovenThe Netherlandswww.boschsecurity.com© Bosch Security Systems B.V., 2013
– If unsure of the type of power supply to use, contact your dealer or local powercompany.12. Servicing - Do not attempt to service this unit yourself
All rights reserved.DisclaimerUnderwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of thesecurity or signaling aspects o
All-pole power switch - Incorporate an all-pole power switch, with a contact separation of atleast 3 mm in each pole, into the electrical installation
Pluggable equipment - Install the socket outlet near the equipment so it is easily accessible.Power resupply - If the unit is forced to power down due
instructions, générer des interférences nuisibles aux communications radio. L’utilisation de ceproduit dans une zone résidentielle peut provoquer des
Comments to this Manuals