DCN multimediaConference System en Hardware Installation Manual
Hardware requirementsSwitchesThe following minimal requirements apply to switches:– 1 Gbit or higher with hardware switching capabilities.– Quality of
RoutersThe following minimal requirements apply to routers:– 1 Gbit or higher Ethernet ports.– Supports PIM‑DM or Bidirectional PIM.– Performs IP rout
Power supply capacity calculation planHow to startFirst decide how to supply power to the devices:– Using DCNM‑APS and DCNM‑PS– Using PoE Ethernet swi
Rear view10 12 13 15 17 191114 16 18 201 2 3 4 5 6 7 8 9Figure 4.2: DCNM‑APS10 12 13 15 1714 16 1819209Figure 4.3: DCNM‑PS ItemDescription1, 5 XLR lin
Network and Power connector Max. power output (W) Max. devicesSocket 1 (12) No power capacity. ---Socket 2 (13) 15 1Socket 3 (15) 144 10Socket 4 (17)
Notice!Make sure one socket can supply power to the complete redundant chain.Calculation using PoE switchesSelect one or more PoE Ethernet switches to
Installation material and toolsThis section describes installation material such as cables, connectors and tools.Recommedations– Always use manufactur
DCNM-CBCON System Network Cable Connector (50 pcs)You can make your own system network cables by using:– The system network connector (this section).–
DCNM-CBTK System Network Cable ToolkitThe system network cable toolkit is used to connect the DCNM-CBCON System Network CableConnector (50 pcs), page
DCNM-CB250 System Installation CableThe system network installation cable, without connectors, is available in a length of 250meters and is used for m
Mechanical installation of Central EquipmentDCNM-APS and DCNM-PSThe DCNM‑APS Audio Powering Switch is used to:– control system audio signals,– route a
Rear view10 12 13 15 17 191114 16 18 201 2 3 4 5 6 7 8 9Figure 6.1: DCNM‑APS10 12 13 15 1714 16 1819209Figure 6.2: DCNM‑PS ItemDescription1, 5 XLR lin
How to install1. Install the DCNM‑APS or DCNM‑PS in a 19 inch device rack system or on a flat surface.Two 19 inch mounting brackets and four bottom fe
Mechanical installation of Contribution DevicesDCNM-MMD Multimedia DeviceTypically, the DCNM‑MMD is used to:– Add participants to a meeting.– Monitor
How to connectThe system can be quickly and easily configured as a daisy‑chain configuration (see Typicalsystem setup, page 7), or as a star configura
See also– DCNM-CBxx System Network Cable, page 16– DCNM-CB250 System Installation Cable, page 19 DCN multimedia Mechanical installation of Contributio
DCNM-HDMIC High Directive MicrophoneThe high directive microphone is typically used with the:– DCNM-MMD Multimedia Device, page 23. 36471258Figure 7.3
How to connect or remove the microphoneThe microphone can be easily connected to the DCNM-MMD Multimedia Device, page 23:964857Figure 7.4: DCNM‑HDMIC
DCNM-NCH Name Card HolderThe name card holder (1) has two magnets (2) located on top of the name card holder andcan therefore be easily attached to, a
Installation TestAn installation test is needed to prevent connection mismatches and find potential productdefects at an early stage. Not to do so cou
Table of contents1Safety 42About this manual 52.1 Intended audience 52.2 Alerts and notice signs 52.3 Copyright and disclaimer 52.4 Document history 5
– Downloading devices is not covered in this manual. Refer to the DCN mulimediaconfiguration manual on how to download the devices. Customer serviceIf
Bosch Security Systems B.V.Torenallee 495617 BA EindhovenThe Netherlandswww.boschsecurity.com© Bosch Security Systems B.V., 2013
SafetyPrior to installing or operating products, always read the Important Safety Instructions whichare available as a separate multilingual document:
About this manualThe purpose of this manual is to provide information required for installing the DCNmultimedia conference system.This installation ma
System installation overviewIt is advisable to participate in the DCN multimedia conference system training before youinstall, prepare, configure and
Typical system setup1824398866665888765.15.2Figure 3.1: Typical DCN multimedia system overview A typical DCN multimedia conference system consists of:
System installation design and planningBefore you start to install system devices and connect system cabling, you should make asystem design and plann
12 2 2 22 2 2 2Figure 4.1: Example: Switch-levels Power supply capacityThe total system network cable length and connected devices determine the requi
Comments to this Manuals