- 1 - INSTALLATION INSTRUCTION EX30 Infrared Imager™
- 10 - 1. MOUNTING BRACKET PREPARATION • Use the supplied Allen Key to remove the setscrew from the supplied mounting bracke
- 11 - 2. CABLE / BRACKET INSERTION EX30 Camera • Carefully feed the Power/BNC cable through both sections of the mounting bracket. • Ma
- 12 - 3. MOUNTING BRACKET ATTACHMENT • Attach the Mounting Bracket to the Camera’s Mounting Block using the six bolts supplied with
- 13 - 4. CAMERA MOUNTING Warning: this apparatus must be securely attached to the wall or ceiling in accordance with installation instructions. Fai
- 14 - • Installation should only be performed by skilled personnel Hardware required: • For ceiling mount: 1. Mounting Bracket, Model EXMB.029,
- 15 - mounting using the following wood screws secured into a 2x4 stud under ½” drywall: • wood screws with washer, 1/4” lag, dia Ø1/4”, 2” long, 9
- 16 - 5. CAMERA LENS ADJUSTMENTS AND SELECTING THE WINDOW For optimum picture quality, the camera lens should be as close as possible to the inside
- 17 - 5.1. Vari Focal and “Auto-Iris” Control Adjustments • Loosen the lens set screws for focus/zoom adjustments. • The se
- 18 - Use a Neutral Density filter or Infra-Red Pass filter to cover the lens during focusing to simulate low light conditions on scene for co
- 19 - 6. LED ARRAY - POWER ADJUSTMENTS If adjustment is needed, remove the rear cover for access to the LRB. The EX30 needs to be powered-up while
- 2 - IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep this instruction. 3. Heed all warnings. 4. Follow all instru
- 20 - 7. OSD ADJUSTMENT 1. Open the back cover of EX30 to access the OSD controls. 2. Enter the OSD menu by pressing the joystick button down. 3
- 21 - 8. OSD MENU
- 22 - Note The following default settings should not be changed: Lens = DC; E.Shutter = Auto
- 24 -
- 25 -
- 26 -
- 27 -
- 28 - Note The following default setting should not be changed. Day & Night = Auto
- 3 - 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the power where they exit from t
- 30 -
- 31 -
- 32 -
- 33 -
- 34 -
- 35 -
- 36 -
- 37 -
- 38 -
- 39 -
- 4 - ® IMPORTANTFor best results, please read this Instruction Booklet prior to installing theEX30 Infrared Imager. WARNI NG !CSA Certified
- 40 - 9. CAMERA RE-ASSEMBLY Make sure all wires are properly connected, all holes are sealed against moisture penetration, and all mounting screws a
- 41 - 10. TROUBLESHOOTING GUIDE -CAMERA PROBLEM POSSIBLE CAUSE LIKELY SOLUTION No Video 1. Power Supply: -Conne
- 42 - Poor Picture Quality Dim Image Snowy Image Iris closed Poor Video Signal Noisy Power Supply
- 43 - Horizontal Scan Lines, Rolling Up or Down Negative, scrambled, or faded image Ground Looping on video cable Low voltage
- 44 -
- 45 - 11. TROUBLESHOOTING GUIDE – LEDs PROBLEM POSSIBLE SOLUTION Fuse Blows - Check the fuse rating. - Check for shorting between the housing and
- 46 - 12. MOUNTING HOLE - DIAGRAM • All dimensions expressed in millimeters • 1.59” X 3.38” in inches
- 47 - 13. GENERAL SPECIFICATIONS Power Consumption: 36W Max. Maximum Current: 3.0A @12Vdc Input Voltage: 24VAC 12VDC Enclosure (ho
- 48 - Note:
- 49 - Americas Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, Pennsylvania 17601 USA Telephone+ 1 888-289-
- 5 - NOTE: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC rules. These limit
- 6 - INDEX – EX30 Infrared Imager™ PAGE DESCRIPTION... 7 UNPACKING...
- 7 - DESCRIPTION The EX30 Infrared Imager consists of an LXR camera and an infrared illuminator. This surveillance system gives optimum performan
- 8 - UNPACKING Care should be taken when unpacking the shipped unit. Check the parts list and confirm all items have been located. Inspect the equip
- 9 - INITIAL PREPARATIONS • Determine the operating voltage at the installation site. The camera‘s Voltage Regulator Board accepts both 10.5-40VD
Comments to this Manuals