Bosch PTA 2000 Operations Instructions download pdf (Page 13)

English | 13

Bosch Power Tools 1 619 929 K24 | (28.3.12)

Assembly

Delivery Scope

Before assembling the saw stand, check if all parts listed be-

low are provided:

– Saw stand PTA 2000

– Fastening kit 9 consisting of:

Hexagon bolt M8 x 45 (3 pce.),

Hexagon bolt M8 x 55 (1 pce./PPS 7 S),

Hexagon bolt M8 x 35 (1 pce./PTS 10),

Washers (4 pce.),

Self-locking nuts with serrated bearing, M8 (4 pce.)

Additionally required tools (not in delivery scope):

– Open-end spanner (13 mm) (2 pce.)

– Allen key (5 mm)

Preparing the Saw Stand

Setting Up the Saw Stand (see figure A)

Set up the saw stand first before fastening the power tool.

– Lay the saw stand on the floor (legs facing downward).

– Loosen the locking knob 5, if required.

– Position one foot on the transport handle 8, release the

lock/release button 2 and pull handle 1 upward until the

limit bolt engages.

– Tighten the locking knob 5 again.

Fastening the Power Tool

(PPS 7S: see figure B1)

(PTS 10: see figure B2)

Mount the power tool onto the saw stand in such a manner

that the power tool's operating elements are located above

the wheels.

– Position the power tool in the transport position. Notes on

the transport position are given in the operating instruc-

tions of the respective power tool.

– Turn and move the retaining adapters 4 as shown in the fig-

ure to the matching position for the corresponding power

tool (PPS 7: marks 2; PTS 10: marks 1).

– Position the power tool on the retaining adapters in such a

manner that the mounting holes on the power tool are

brought into alignment with the slots of the retaining

adapters.

– Screw the retaining adapters and the power tool together

with the hexagon bolts, washers and self-locking nuts from

the fastening kit 9.

Operation

Working Advice

Before working, always make sure that the locking knob 5 is

firmly tightened.

Do not overload the saw stand. Always observe the maximum

carrying capacity of the saw stand.

Always hold the workpiece firmly, especially the longer and

more heavy section. After cutting through the workpiece, the

centre of gravity may become dislocated in such an unfavour-

able manner that the workpiece sections tip over.

Support long and heavy workpieces at the free end (e.g., with

the Bosch PTA 1000 roller stand).

Resting Bar

The resting bar 6 enables upright and place-saving storage of

the saw stand with a power tool mounted. Ideally, the saw

stand with the mounted power tool is set against a wall, in or-

der to prevent it from tipping over.

– Press the limit bolts 10 of the resting bar in and fold the

resting bar 6 completely inward until the limit bolts engage

again.

Transport (see figures D1– D4)

The saw stand must be folded together for transport.

– Press the limit bolts 10 of the resting bar in and fold the

resting bar 6 completely outward until the limit bolts en-

gage again.

– Loosen locking knob 5.

– Position one foot on the foot lever 8 and pull the handle 1

slightly upward in order to relieve the limit bolts.

– Pull lock button 2 completely outward and slowly guide the

saw stand down by the handle.

– Tighten the locking knob 5 again.

– Grasp and raise the saw stand by the transport handle 8.

Maintenance and Service

Maintenance

If the saw stand should fail despite the care taken in manufac-

ture and testing, repair should be carried out by an authorised

customer services agent for Bosch power tools.

In all correspondence and spare parts orders, please always

include the 10-digit article number given on the type plate of

the saw stand.

After-sales Service and Customer Assistance

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. Exploded views and information on spare parts can al-

so be found under:

www.bosch-pt.com

Our customer service representatives can answer your ques-

tions concerning possible applications and adjustment of

products and accessories.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham

Uxbridge

UB 9 5HJ

Tel. Service: +44 (0844) 736 0109

Fax: +44 (0844) 736 0146

E-Mail: boschse[email protected]

OBJ_BUCH-1563-002.book Page 13 Wednesday, March 28, 2012 1:05 PM

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 75 76

Comments to this Manuals

No comments

Bosch PTA 2000 Operations Instructions Page 13

Comments to this Manuals