VIDEOJET multi 4000VJM-4016 en Installation Manual
SummaryThe VIDEOJET multi 4000 encoder provides the following main functions:– Video, audio, and data transmission over IP data networks– Dual Streami
Connections, controls and displaysFront view1 Factory reset buttonto restore factory default settings2 LED ACTIVITYflashes during data transmission3 L
Rear view1 VIDEO IN 1 to VIDEO IN 16 video inputsBNC socket for connecting the video source2 ETH RJ45 socketfor connecting to an Ethernet LAN (local n
InstallationPreparationsThe VIDEOJET multi 4000 encoder is designed for installation in a switch cabinet. Mountingthe unit in a 19-inch rack using the
14 en | Installation VIDEOJET multi 40002014.02 | V1 | F.01U.298.750 Installation Manual Bosch Sicherheitssysteme GmbH
ConnectionConnecting camerasYou can connect a maximum of 16 video sources to the VIDEOJET multi 4000 encoder. Anycameras and other video sources that
Establishing the network connectionYou can connect the unit to a 10/100/1000 Base-T network using a standard UTP category 5cable with RJ45 plugs.4 Con
Connecting audioThe unit has two audio ports for audio line signals.The audio signals are transmitted two-way and in sync with the video signals. The
Connecting alarm inputs and relay outputNotice!For correct connection of alarm inputs and relay outputs, observe the labelling on the unit.Alarm input
2. Connect the terminal block to the socket on the unit observing the labeling.See also– Terminal block, page 25Creating a serial connectionNotice!For
Power on/power offDepending on the ordered product package, the unit is delivered together with a power cord.Notice!Use only a suitable power cord. Wh
ConfigurationSetupBefore you can operate the unit within your network, it must have a valid IP address for yournetwork and a compatible subnet mask.No
Additional parametersYou can check and set additional parameters with the assistance of the Configuration Managerapplication in Video Client. You can
TroubleshootingContactIf you are unable to resolve a malfunction, please contact your supplier or systems integrator,or go directly to Bosch Security
Malfunction Possible causes Recommended solutionControl of cameras orother units is notpossible.The cable connection betweenthe serial interface and t
STATUS LEDLights up: Startup in progress.Flashes: The unit is faulty, for example following failed firmwareupload.CONNECT LEDLights up: The unit is sw
The serial interface supports the RS-232, RS-422 and RS-485 transmission standards. Themode used depends on the current configuration.The pin assignme
MaintenanceUpdatesFirmware updates are carried out via our Video Client software or other management systemsin use. Please refer to the relevant docum
DecommissioningTransferVIDEOJET multi 4000 should only be passed on together with this installation manual.DisposalYour Bosch product is designed and
Technical dataElectricalInput voltage 100 to 240 V AC, 47 to 63 HzInput current 0.32 to 0.15 APower consumption 23 W maxConnectors IEC 320 C14Mechanic
Table of contents1Safety 51.1 Electric shock hazard 51.2 Installation and operation 51.3 Maintenance and repair 62Short information 72.1 About this ma
Total delay 260 ms typicalDual Streaming Full performance and full frame rate on both streams for everyvideo input channelFrame rate 1 to 25/30 ips (P
IndexAAlarm, 12Alarm input, 18Audio connections, 12, 17CCameras, 15Closing contact, 18Conventions, 7DDanger, 5Data interface, 19DefaultIP address, 21D
Bosch Sicherheitssysteme GmbHRobert-Bosch-Ring 585630 GrasbrunnGermanywww.boschsecurity.com© Bosch Sicherheitssysteme GmbH, 2014
10Technical data 2910.1 Electrical 2910.2 Mechanical 2910.3 Environmental conditions 2910.4 Standards 294 en | Table of Contents VIDEOJET multi 400020
SafetyElectric shock hazard– Never attempt to connect the unit to any power network other than the type for which itis intended.– Connect the unit to
– When making connections, use only the cables supplied or use appropriate cablesimmune to electromagnetic interference.– Position and run all cables
Short informationAbout this manualThis manual is intended for persons responsible for the installation and operation of theVIDEOJET multi 4000 encoder
System overviewParts included– 1 VIDEOJET multi 4000 video encoder– 1 accessory bag– 1 Installation Manual– optional: 1 power cord (depending on the o
Audio encodingThe VIDEOJET multi 4000 encoder uses the G.711, AAC, and L16 audio compressionstandards. G.711 is the default setting for live transmiss
Comments to this Manuals