Bosch GBH 36 VF-LI Specifications download pdf (Page 18)

18 | English

1 609 92A 04C | (14.12.12) Bosch Power Tools

used (e.g., drills with cylindrical shank). For these tools, a

keyless chuck or a key type drill chuck are required.

GBH 36 VF-LI: The SDS-plus quick change chuck

can easily be

replaced against the quick change keyless chuck

provided.

Changing the Key Type Drill Chuck (GBH 36 V-LI)

To work with tools without SDS-plus (e.g., drills with cylindri-

cal shank), a suitable drill chuck must be mounted (key type

drill chuck or keyless chuck, accessories).

Mounting the Key Type Drill Chuck (see figure C)

– Screw the SDS-plus adapter shank 22 into a key type drill

chuck 21. Secure the key type drill chuck 21 with the se-

curing screw 20. Please observe that the securing

screw has a left-hand thread.

Inserting the Key Type Drill Chuck (see figure D)

– Clean the shank end of the adapter shank and apply a light

coat of grease.

– Insert the key type drill chuck with the adapter shank into

the tool holder with a turning motion until it automatically

locks.

– Check the locking effect by pulling the key type drill chuck.

Removing the Key Type Drill Chuck

– Push the locking sleeve 5 toward the rear and pull out the

key type drill chuck 21.

Removing/Inserting the Quick Change Chuck

(GBH 36 VF-LI)

Removing the Quick Change Chuck (see figure E)

– Pull the lock ring for the quick change chuck 6 toward the

rear, hold it in this position and pull off the SDS-plus quick

change chuck 2 or the quick change keyless chuck 1 to-

ward the front.

– After removing, protect the replacement chuck against

contamination.

Inserting the Quick Change Chuck (see figure F)

– Before inserting, clean the quick change chuck and apply a

light coat of grease to the shank end.

– Grasp the SDS-plus quick change chuck 2 or the quick

change keyless chuck 1 completely with your hand. Slide

the quick change chuck with a turning motion onto the drill

chuck mounting 23 until a distinct latching noise is heard.

– The quick change chuck is automatically locked. Check the

locking effect by pulling the quick change chuck.

Changing the Tool

The dust protection cap 4 largely prevents the entry of drilling

dust into the tool holder during operation. When inserting the

tool, take care that the dust protection cap 4 is not damaged.

 A damaged dust protection cap should be changed im-

mediately. We recommend having this carried out by

an after-sales service.

Inserting SDS-plus Drilling Tools (see figure G)

The SDS-plus drill chuck allows for simple and convenient

changing of drilling tools without the use of additional tools.

– GBH 36 VF-LI: Insert the SDS-plus quick change chuck 2.

– Clean and lightly grease the shank end of the tool.

– Insert the tool in a twisting manner into the tool holder until

it latches itself.

– Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus drilling tool can

move freely. This causes a certain radial run-out at no-load,

which has no effect on the accuracy of the drill hole, as the

drill bit centres itself upon drilling.

Removing SDS-plus Drilling Tools (see figure H)

– Push back the locking sleeve 5 and remove the tool.

Inserting Drilling Tools without SDS-plus (GBH 36 V-LI)

Note: Do not use tools without SDS-plus for hammer drilling

or chiselling! Tools without SDS-plus and their drill chucks are

damaged by hammer drilling or chiselling.

– Insert a key type drill chuck 21 (see “Changing the Key

Type Drill Chuck”, page 18).

– Open the key type drill chuck 21 by turning until the tool

can be inserted. Insert the tool.

– Insert the chuck key into the corresponding holes of the

key type drill chuck 21 and clamp the tool uniformly.

– Turn the mode selector switch 11 to the “drilling” position.

Removing Drilling Tools without SDS-plus (GBH 36 V-LI)

– Turn the sleeve of the key type drill chuck 21 with the drill

chuck key in anticlockwise direction until the drilling tool

can be removed.

Inserting Drilling Tools without SDS-plus (GBH 36 VF-LI)

(see figure I)

Note: Do not use tools without SDS-plus for hammer drilling

or chiselling! Tools without SDS-plus and their drill chucks are

damaged by hammer drilling or chiselling.

– Insert the quick change keyless chuck 1.

– Firmly hold the retaining ring 25 of the quick change

chuck. Open the tool holder by turning the front sleeve 24

until the tool can be inserted. Tightly hold the retaining ring

25 and firmly turn the front sleeve 24 in the direction of the

arrow until a distinct latching noise can be heard.

– Check the tight seating by pulling the tool.

Note: If the tool holder was opened to the stop, then the latch-

ing noise possibly may be heard while closing the tool holder

and the tool holder will not close.

In this case, turn the front sleeve 24 once in the opposite di-

rection of the arrow. Afterwards, the tool holder can be

closed (tightened) again.

– Turn the mode selector switch 11 to the “drilling” position.

Removing Drilling Tools without SDS-plus (GBH 36 VF-LI)

(see figure J)

– Firmly hold the retaining ring 25 of the quick change

chuck. Open the tool holder by turning the front sleeve 24

in the direction of the arrow until the tool can be removed.

Dust Extraction with the Dust Extraction Attach-

ment (Accessory)

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

OBJ_BUCH-283-006.book Page 18 Friday, December 14, 2012 1:10 PM

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 237 238

Bosch GBH 36 VF-LI Specifications Page 18

Comments to this Manuals

Bosch GBH 36 VF-LI Specifications Page 18

Comments to this Manuals

Related products and manuals for Cordless rotary hammers Bosch GBH 36 VF-LI