Bosch PSM 18LI Specifications download pdf (Page 15)

English | 15

Bosch Power Tools 2 609 007 287 | (17.6.13)

Position the sanding sheet 4 flush alongside one edge of the

sanding plate 5, then lay the sanding sheet onto the sanding

plate and press firmly.

To remove the sanding sheet 4, grasp it at one of the tips and

pull it off from the sanding plate 5.

Sanding sheets of the Bosch Delta Sander can be used.

Sanding accessories, such as fleece pads/polishing cloth

pads, are attached to the sanding plate in the same manner.

Selecting the Sanding Sheet

Depending on the material to be worked and the required rate

of material removal, different sanding sheets are available:

For reworking or polishing, especially of metal and stone, use

fleece/polishing cloth pad.

Depending on the desired surface quality of the workpiece,

different fleece types or polishing cloth pads are to be used.

Replacing the Sanding Plate (see figure F)

 Slide the SDS button for release of the sanding plate 6 all

the way to the right.

 Remove the sanding plate 5.

 Guide the sanding plate 5 from below against the sand-

ing plate holder and firmly press them together.

 Slide the SDS button for release of the sanding plate 6 all

the way to the left.

If, e. g., the front tip of the sanding sheet is worn, you can also

remove the complete sanding plate and reattach it turned by

120°.

Specialty Sanding Plates

You can replace the supplied sanding plate 5 with a specialty

sanding plate, which is available as an accessory.

The specialty sanding plate is attached in the same manner as

the one supplied.

Attach and remove the respective sanding sheets in the same

manner as when changing original sanding sheets.

Pad Extender (see figure G)

With the pad extender 14 you can sand surfaces that are diffi-

cult to access, such as sills on windows, cabinets or doors.

Pad Extender, Narrow (see figure H)

With the narrow pad extender 15 you can sand narrow open-

ings, slots and passages.

Pad Extender, Narrow Rounded (see figure I)

The narrow rounded pad extender 17 allows you to sand

curved and hollow areas or surfaces that are curved inward,

such as on furniture, rails or heating radiators.

Operation

Starting Operation

Inserting the battery

 Use only original Bosch lithium ion batteries with the

voltage listed on the nameplate of your power tool. Us-

ing other batteries can lead to injuries and pose a fire haz-

ard.

Switching On and Off

To start the machine, push the ON/Off switch 8 downward to

position “1”.

To switch off the machine, push the On/Off switch 8 upward

to positon “0”.

To save energy, only switch the power tool on when using it.

Battery Charge-control Indication

The battery charge-control indicator 7 indicates the charge

condition of the battery when the machine is switched on. It

consists of 3 green LEDs.

Temperature Dependent Overload Protection

When using as intended for, the power tool cannot be subject

to overload. When the load is too high or the allowable battery

temperature of 70 °C is exceeded, the electronic control

switches off the power tool until the temperature is in the op-

timum temperature range again.

The 3 LEDs of the battery charge-control indicator 7 flash rap-

idly when the battery temperature is not within the operating

temperature range of –20 to +70°C, and/or when the over-

load protection has responded.

Protection Against Deep Discharging

The Lithium-Ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Grain size

For the working of all wooden

materials

40—180

For coarse-sanding, e. g. of rough,

unplaned beams and boards

coarse 40

For face sanding and planing small

irregularities

medium 80, 120

For finish and fine sanding of wood fine 180

For the working of paint/enamel

coats or primers and fillers

40—180

For sanding off paint coarse 40

For sanding primer medium 80, 120

For final sanding of primers before

coating

fine 180

LED Capacity

Continuous lighting 3 x green ≥ 66%

Continuous lighting 2 x green 34—65%

Continuous lighting 1 x green 11—33%

Slow flashing 1 x green ≤ 10%

OBJ_BUCH-1201-002.book Page 15 Monday, June 17, 2013 11:30 AM

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 85 86

Comments to this Manuals

No comments

Bosch PSM 18LI Specifications Page 15

Comments to this Manuals

Related products and manuals for Cordless sanders Bosch PSM 18LI