Bosch IntuiKey Instruction Manual download pdf (Page 4)

KBD-SFTCFG | Instruction Manual | Installation

Bosch Security Systems | December 02, 2005

6.0 INSTALLATION

6.1 Software Installation

Insert the CD into the PC’s CD-ROM drive. If the CD

ROM drive is not configured to autorun, open

Windows Explorer and navigate to the

ICS_Installer.exe. Double click to begin the installation.

6.2 RS-232 Connection

All communication between the IntuiKey Series

keyboard and the KBD-SFTCFG is performed through

an RS-232 interface.

Connect one end of the RS-232 interface cable to the

9-pin RS-232 Serial Port located on the far right side

of the rear of the IntuiKey keyboard. Connect the

other end of the RS-232 interface cable to a COM

port on the PC. The software supports the use of

COM1 through COM16.

Figure 2 – IntuiKey Keyboard Rear Panel Showing

9-pin RS-232 Interface Connector

If an Allegiant software package (LTC 8059/00 or

LTC 8850/00) will be used simultaneously with the

KBD-SFTCFG, a second COM port must be available

on the PC to interface with the Allegiant system’s

console port. Refer to the manual provided with the

Allegiant software for complete information.

6.3 Keyboard Preparation

First, verify that the keyboard’s firmware version is

1.01 or higher. The firmware version is shown on the

IntuiKey keyboard’s main menu when it is first

powered up. If the firmware version precedes version

1.01, a keyboard firmware update is required before it

can be used with the KBD-SFTCFG. Update the

IntuiKey keyboard’s firmware via the IntuiKey

Firmware Update Utility, available from the Software

Updates section of the BOSCH Web site

(http://www.boschsecurity.com).

IMPORTANT: Before the IntuiKey keyboard will

respond to external RS-232 communication, it must be

placed in bootloader mode. This is done by entering the

IntuiKey keyboard’s Firmware Upgrade menu which is

accessed from the Keyboard Control option of the

main Product List selection screen. When prompted for

the password, press the 1 and 0 numeric keypad

buttons simultaneously. The keyboard will then be in

bootloader mode.

Figure 3 – IntuiKey Keyboard Bootloader Menu Access

In certain circumstances, it may be necessary to enter

bootloader mode when the keyboard is in a state

where the menu selections are not visible or are

otherwise unavailable. In this situation, bootloader

mode can be entered directly by simultaneously

pressing the 1 and 0 numeric keypad buttons while the

power/data cable is attached. The buttons must be released

immediately when the keyboard begins to power up and

initialize. For keyboards with bootloader version 1.01 or

higher, skip the next paragraph.

For keyboard bootloader version 1.00 only, you

must now press the CLR button, power off/on the

keyboard again, allow several seconds for it to boot up

to a menu, then power it off/on while pressing the

1 and 0 numeric keypad buttons as the power/data

cable is attached. Again, release the buttons immediately

when the keyboard begins to power up and initialize.

The keyboard will now be able to communicate with

the KBD-SFTCFG. If multiple transfers will be made,

the keyboard may need to be cleared and the

bootloader mode re-entered after each action.

Keyboard models containing Bootloader version 1.05

or later support the ability to download / upload using

a faster baud rate of 57600. Once you are in the

Bootloader menu, check the lower right section of the

larger LCD screen. If you see the option for baud rate

selection, press the button to select the faster rate. Your

data will transfer three (3) times faster compared to

using the default baud rate of 19200.

MUX / DVR ALLEGIANT 12 VDC RS-232 SERIAL PORT

Allegiant

ADIM

DVR 1

Unit a

Keyboard

Control

Exit

Factory Firmware

Reset Upgrade

Language

Select

Keyboard Contrast

Test Adjust

LCD Key Click

Test On/Off

Joystick Display

Auto Cal. Inverse

Normal

1 2 3 4 5 6 7 8 9 ... 23 24

Comments to this Manuals

Dayanazem 17 Apr 2024 | 14:06:04

Slightly off topic :) It so happened that my sister found an interesting man here, and recently got married ^_^ (Moderator, don't troll!!!) Is there are handsome people here! ;) I'm Maria, 28 years old. I work as a model, successfull - I hope you do too! Although, if you are very good in bed, then you are out of the queue!))) By the way, there was no sex for a long time, it is very difficult to find a decent one... And no! I am not a prostitute! I prefer harmonious, warm and

Bosch IntuiKey Instruction Manual Page 4

Comments to this Manuals

Related products and manuals for Keyboards Bosch IntuiKey