133
Toll Free: 877-BOSCH-99
Boschtools.com
Bits
Carbide Tipped Beading Stile & Rail Bits
Micrograin bits with shear angle geometry, super-sharp cutting edges and
close-tolerance manufacturing to ensure consistently smooth, tight-fitting joints.
• Recommended for use with a router table. Designed for 3/4" wood with
a maximum wood thickness of 7/8"
• 85621M is a control cut bit
Carbide Tipped Face Frame/Flush Trim, V-groove Bits
Micrograin bits used to flush face frame to cabinet side while at
the same time cutting a V-groove down cabinet joint. Also used
for creating a decorative V-groove cut.
Item #
A.
Overall
Dia.
B.
Cutting
Edge Lgth.
C.
Shank
Dia.
D.
Overall
Length
E.
Decorative
Cut Depth
F.
Kerf
G.
Bearing
Diameter
R.
Radius
85621M 1-5/8" 5/8" 1/2" 3" 5/8" 1/4" 7/8"(22 mm) 7/32"
85622M 1-5/8" 57/64" 1/2" 3" 1-5/8" 1/4" 7/8"(22 mm) 1/2"
85620M Beading stile and rail set includes 85621M and 85622M assemblies
Item #
A.
Overall
Diameter
B.
Cutting
Edge Lgth.
C.
Shank
Diameter
D.
Overall
Length
E.
Angle Bearing
Diameter
85646M 5/8" 1" 1/4" 2-1/2" 90° 1/2"
85647M 5/8" 1" 1/2" 3 90° 1/2"
Carbide Tipped Ogee Stile & Rail Bits
Micrograin bits with shear angle geometry, super-sharp cutting edges and
close-tolerance manufacturing to ensure consistently smooth, tight-fitting joints.
• These bits are not for use in hand-held routers. Use with a router table only.
Designed for 3/4" wood with a maximum wood thickness of 7/8"
• Both 85626M and 85627M assemblies are reversible. Either can be used
to make both stile and rail cuts by order on the arbor. This requires one
workpiece to be cut ”face up“ and the other workpiece ”face-down”
Item #
A.
Overall
Dia.
B.
Cutting
Edge Lgth.
C.
Shank
Dia.
D.
Overall
Length
E.
Decorative
Cut Depth
F.
Kerf
G.
Bearing
Diameter
R.
Radius
85626M 1-5/8" 43/64" 1/2" 3" 13/32" 3" 7/8"(22 mm) 1/2"
85627M 1-5/8" 51/64" 1/2" 3" 17/64" 3" 7/8"(22 mm) 1/2"
85625M Ogee stile and rail set includes 85626M and 85627M assemblies
Replacement Stile & Rail Cutters
85630M
Use with all four
assemblies.
85623M 85624M
85628M 85629M
Item #
A.
Overall
Diameter
B.
Cutting
Edge Lgth.
C.
Inside
Diameter
R.
Cutting
Radius Type
85623M 1-7/16" 25/64" 8 mm 27/64" Beading
85624M 1-39/64" 13/32" 8 mm 7/16" Beading
85628M 1-39/64" 17/64" 8 mm 13/32" Ogee
85629M 1-5/8" 1-1/16" 8 mm 13/32" Ogee
85630M 1-5/8" 1/4" 8 mm N/A
Router
Comments to this Manuals