English | 9
Bosch Power Tools 1 619 X05 390 | (25.11.10)
– Press the spindle lock button 3 and keep it
pressed.
f The spindle lock button 3 may be actuated
only when the saw spindle is at a standstill.
Otherwise, the power tool can be damaged.
– Unscrew clamping bolt 20 with ring spanner
21 in rotation direction n.
– Tilt back the retracting blade guard 11 and
hold firmly.
– Remove the clamping flange 19 and the saw
blade 18 from the saw spindle 16.
Mounting the Saw Blade (PKS 184)
(see figure A)
– Clean the saw blade 18 and all clamping
parts to be assembled.
– Tilt back the retracting blade guard 11 and
hold firmly.
– Place the saw blade 18 on to the mounting
flange 17. The cutting direction of the teeth
(direction or arrow on saw blade) and the di-
rection-of-rotation arrow on the blade guard
14 must correspond.
– Mount the clamping flange 19 and screw in
the clamping bolt 20 turning in rotation di-
rection o. Observe correct mounting posi-
tion of mounting flange 17 and clamping
flange 19.
– Press the machine via the saw blade 18
against a piece of wood in order to lock the
saw spindle 16 in place.
– Tighten the clamping bolt 20 with ring span-
ner 21 in rotation direction o. The tightening
torque is 6–9 Nm, which corresponds with
hand-tight plus ¼ turn. When the clamping
bolt 20 is tightened to tightly, the saw blade
can no longer be removed.
Mounting the Saw Blade (PKS 1500)
(see figure A)
For changing the cutting tool, it is best to place
the machine on the face side of the motor hous-
ing.
– Clean the saw blade 18 and all clamping
parts to be assembled.
– Tilt back the retracting blade guard 11 and
hold firmly.
– Place the saw blade 18 on to the mounting
flange 17. The cutting direction of the teeth
(direction or arrow on saw blade) and the di-
rection-of-rotation arrow on the blade guard
14 must correspond.
– Mount the clamping flange 19 and screw in
the clamping bolt 20 turning in rotation di-
rection o. Observe correct mounting posi-
tion of mounting flange 17 and clamping
flange 19.
– Press the spindle lock button 3 and keep it
pressed.
– Tighten the clamping bolt 20 with ring span-
ner 21 in rotation direction o. The tightening
torque is 6–9 Nm, which corresponds with
hand-tight plus ¼ turn. When the clamping
bolt 20 is tightened to tightly, the saw blade
can no longer be removed.
Dust/Chip Extraction
f Before any work on the machine itself, pull
the mains plug.
f Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metal can be harmful to one’s health. Touch-
ing or breathing-in the dusts can cause aller-
gic reactions and/or lead to respiratory infec-
tions of the user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in
connection with wood-treatment additives
(chromate, wood preservative). Materials
containing asbestos may only be worked by
specialists.
– Provide for good ventilation of the work-
ing place.
– It is recommended to wear a P2 filter-
class respirator.
Observe the relevant regulations in your
country for the materials to be worked.
OBJ_BUCH-1089-002.book Page 9 Thursday, November 25, 2010 8:04 AM
(32 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals