Bosch 18636-03 Use and Care Manual download pdf (Page 15)

-15-

$0=A4.0

!&$# $#'

"#%$ $ 0C.0;? 1:=

?30 =0;7,.0,-70 .,=-:9 -=@>30>

"=0A09?4A0 8,49?09,9.0 ;0=1:=80/ -D

@9,@?3:=4E0/ ;0=>:9907 8,D =0>@7? 49

84>;7,.492 :1 49?0=9,7 B4=0> ,9/

.:8;:909?> B34.3 .:@7/ .,@>0 >0=4:@>

3,E,=/ We recom mend that all tool service

be performed by a Bosch Factory Service

Center or Authorized Bosch Service Station.

SERVICE MEN: Disconnect tool and/or

charger from power source before servicing.

%%#$

0,70=?1:=-,??0=D;,.6>?3,?,=090,=492

?304=09/:17410 If you notice decreased tool

performance or significantly shorter running

time between charges then it is time to

replace the battery pack. Failure to do so

can cause the tool to operate improperly or

damage the charger.

%!!&#%!

Your Bosch tool has been properly lubricated

and is ready for use.

!%!#$

The motor in your tool has been engineered

for many hours of dependable service. To

maintain peak efficiency of the motor, we

recommend it be examined every six months.

Only a genuine Bosch replacement motor

specially designed for your tool should be

used.

#! #&$$

The brushes and commutator in your tool have

been engineered for many hours of

dependable service.

If your tool runs spo rad ically, loses power,

makes unusual noises or runs at a reduced

speed, check the brushes. To continue using

the tool in this condition will permanently

damage your tool.

Check both brushes. Usually the brushes will

not wear out simul taneously. If one brush is

worn out, replace both brushes.

To check brushes: Disconnect battery pack

from tool. Remove brush cover at the rear part

of housing by loosening screws (Fig. 9).

Insert a screwdriver or similar object into the

red notch of the carbon brush and lift out the

brushes; note which way they face, so that the

brushes can be returned to their original

position. Clean the brush holder openings with

com pressed air or a clean cloth and replace

the brushes and brush covers.

After replacing brushes the tool should be run

at no-load and run it freely at full speed for 2

minutes before using the tool. This will allow

the brushes to “seat” properly and will give

you more hours of life from each set of

brushes.

Only genuine Bosch replacement brushes

specially designed for your tool should be

used.

70,9492

%:,A:4/,..4/09?>,7B,D>

/4>.:990.? ?30 ?::7 ,9/:=

.3,=20= 1=:8 ?30 ;:B0= >@;;7D -01:=0

.70,9492 The tool may be cleaned most

effectively with com pressed dry air. 7B,D>

B0,= >,10?D 2:2270> B309 .70,9492 ?::7>

B4?3.:8;=0>>0/,4=

Ventilation openings and switch levers must

be kept clean and free of foreign matter. Do

not attempt to clean by inserting pointed

objects through opening.

0=?,49 .70,9492 ,209?>

,9/ >:7A09?> /,8,20

;7,>?4. ;,=?> Some of these are: gasoline,

car bon tetrachloride, chlorinated cleaning

solvents, ammonia and household detergents

that contain ammonia.

!

WARNING

,49?09,9.0

FIG. 9

BRUSH

HOLDER

BRUSH

COVER

!

WARNING

!

CAUTION

BM 2610944508 01-12:BM 2610944508 01-12 1/10/12 8:12 AM Page 15

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 47 48

Comments to this Manuals

No comments