Bosch 38636-01 Use and Care Manual download pdf (Page 9)

'#$"! %#!

%##$(%

Your tool is equipped with a variable speed

trigger switch. The tool can be turned "ON" or

"OFF" by squeezing or releasing the trigger.

The speed can be adjusted from the minimum

to maximum nameplate RPM by the pressure

you apply to the trigger. Apply more pressure

to increase the speed and release pressure to

decrease speed (Fig. 1).

To reduce the risk of injury

immediately discontinue use

of the tool if the variable speed control ceases

to function. Subsequent loss of on/off control

of the trigger switch is likely.

!#(##'#$ 

'#%##!

After tool use, lock trigger in

“OFF” position to help prevent

accidental starts and accidental discharge.

Your tool is equipped with a forward/

reversing lever and trigger lock located above

the trigger (Fig. 1). This lever was designed

for changing rotation of the bit, and for locking

the trigger in an “OFF” position.

For forward rotation, (with chuck pointed

away from you) move the lever to the far left.

For reverse rotation move the lever to the far

right. To activate trigger lock move lever to

the center off position.

:9:?.3,920/4=0.?4:9:1

=:?,?4:9 @9?47 ?30 ?::7

.:80> ?: , .:8;70?0 >?:; Shifting during

rotation of the chuck can cause damage to

the tool.

#$% 

Your tool is equipped with two separate gear

ranges, low gear and high gear. Low gear

provides high-torque and slower drilling

speeds for heavy duty work or for driving

screws. High gear provides faster speeds for

drilling lighter work. To change speeds slide

switch, to the high or low position (Fig. 1).

%% %!  If your tool appears to be

running, but the chuck will not turn, check to

make sure the gear shifting switch is pushed

fully into desired setting.

&$%&%

Your tool features 15 clutch settings. Output

torque will increase as the clutch ring, is

rotated from 1 to 15. The drill “ ” position

will lock up the clutch to permit drilling and

driving heavyduty work, and also enables bits

to be changed quickly and easily in the

keyless chuck (Fig. 1).

#

When the trigger switch is released it

activates the brake to stop the chuck quickly.

This is especially useful in the repetitive

driving and removal of screws.

%$%!##

Your tool is equipped with a bit and storage

area that is conveniently located in the handle

base where it is always handy and unlikely to

get lost or misplaced (Fig. 1).

-9-

!;0=,?4929>?=@.?4:9>

CAUTION

WARNING

 $#% %$

Move reverse switch lever to the center “OFF”

position. Remove battery pack and rotate the

clutch ring to the drill bit symbol

“ ”. Rotate the chuck sleeve counter-

clockwise viewing from chuck end, and open

chuck to approximate drill bit diameter. Insert

a clean bit up to the drill bit flutes for small

bits, or as far as it will go for large bits. Close

chuck by rotating the chuck sleeve clockwise

and securely tighten by hand (Fig. 2).

:9:? @>0 ?30;:B0= :1

?30 /=477 B3470 2=,>;492

[email protected]?:7::>09:=?423?09-4? Friction burn

or hand injury is possible if attempting to

grasp the spinning chuck.

WARNING

CHUCK

SLEEVE

FIG. 2

BM 2610944822 01-12:2610944822 01-12 1/10/12 8:14 AM Page 9

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 47 48

Comments to this Manuals

No comments

Bosch 38636-01 Use and Care Manual Page 9

Comments to this Manuals

Related products and manuals for Cordless combi drills Bosch 38636-01