Bosch Uneo Service Manual Page 21
- Page / 123
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
English | 21
Bosch Power Tools 2 609 002 670 | (2.6.08)
Operation
Starting Operation
Setting the Operating Mode
With the selector switch for drilling/hammer
drilling 4, the operating mode of the machine is
selected.
Note: Change the operating mode only when the
machine is switched off! Otherwise, the machine
can be damaged.
To change the operating mode, turn the selector
switch for “drilling/hammer drilling” 4 to the re-
quested position.
Reversing the Rotational Direction
(see figure D)
f Actuate the rotational direction switch 8 on-
ly when the machine is at a standstill.
The rotational direction switch 8 is used to re-
verse the rotational direction of the machine.
However, this is not possible with the On/Off
switch 9 actuated.
Right Rotation: For drilling and driving in screws,
push the rotational direction switch 8 left to the
stop.
The indicator for right rotation 6 lights up
when the On/Off switch 9 is actuated and
the motor is running.
Left Rotation: For loosening and unscrewing
screws and nuts, press the rotational direction
switch 8 through to the right stop.
The indicator for left rotation 7 lights up
when the On/Off switch 9 is actuated and
the motor is running.
Switching On and Off
To start the machine, press the On/Off switch 9
and keep it pressed.
To switch off the machine, release the On/Off
switch 9.
For low temperatures, the power tool reaches
the full hammer/impact capacity only after a cer-
tain time.
Setting the Speed/Impact Rate
The speed/impact rate of the switched on power
tool can be variably adjusted, depending on how
far the On/Off switch 9 is pressed.
Light pressure on the On/Off switch 9 results in
low speed/impact rate. Further pressure on the
switch increases the speed/impact rate.
Battery Charge-control Indication
The battery charge-control indicator 5 indicates
the charge condition of the battery for a few sec-
onds when the On/Off switch 9 is pressed
through halfway of fully.
Temperature Dependent Overload Protection
When using as intended for, the power tool can-
not be subject to overload. When the load is too
high or the allowable battery temperature of
70 °C is exceeded, the electronic control switch-
es off the power tool until the temperature is in
the optimum temperature range again.
Additionally, the battery charge-control indicator
5 flashes green and red at the same time until the
On/Off switch 9
is released.
Working Advice
f Apply the power tool to the screw/nut only
when it is switched off. Rotating tool inserts
can slip off.
Position for hammer drilling in con-
crete or stone
Position for drilling without impact
in wood, metal, ceramic and plastic
as well as for screwdriving
LED Capacity
Continuous lighting, green
> 30%
Continuous lighting, red
≤ 30%
OBJ_BUCH-605-002.book Page 21 Monday, June 2, 2008 10:32 AM
- Allgemeine Sicherheitshinwei 5
- Gerätespezifische 7
- Sicherheitshinweise 7
- Funktionsbeschreibung 8
- Abgebildete Komponenten 9
- Technische Daten 9
- Konformitätserklärung 10
- Akku laden (siehe Bild A) 10
- Werkzeugwechsel 11
- Staub-/Späneabsaugung 11
- Inbetriebnahme 11
- Wartung und Service 12
- Transport 13
- Entsorgung 13
- Änderungen vorbehalten 14
- General Power Tool Safety 15
- Warnings 15
- Machine-specific 16
- Safety Warnings 16
- Battery Charger 17
- Functional Description 18
- Assembly 19
- Changing the Tool 20
- Dust/Chip Extraction 20
- Operation 21
- Maintenance and Service 22
- Disposal 23
- AVERTISSEMENT 24
- Instructions de sécurité 26
- Description du fonctionnement 27
- Ø perçage max 28
- Déclaration de conformité 29
- Mise en marche 30
- Instructions d’utilisation 31
- Nettoyage et entretien 32
- Elimination des déchets 33
- ADVERTENCIA 34
- Instrucciones de seguridad 36
- Cargador 37
- Utilización reglamentaria 37
- Componentes principales 37
- Datos técnicos 38
- Declaración de conformidad 39
- Operación 40
- > 30% 41
- Mantenimiento y servicio 42
- Transporte 43
- Eliminación 43
- Indicações gerais de 44
- Instruções de serviço 46
- Descrição de funções 47
- Dados técnicos 48
- Declaração de conformidade 48
- Montagem 49
- Funcionamento 50
- Manutenção e serviço 51
- Eliminação 52
- AVVERTENZA 53
- Istruzioni di sicurezza 55
- Caricabatterie 56
- Descrizione del funzionamento 57
- Montaggio 58
- Cambio degli utensili 59
- Messa in funzione 60
- Manutenzione ed assistenza 61
- Trasporto 62
- Smaltimento 62
- Algemene veiligheidswaarschu 63
- Gereedschapspecifieke 65
- Functiebeschrijving 66
- Afgebeelde componenten 67
- Technische gegevens 67
- Conformiteitsverklaring 68
- Inzetgereedschap wisselen 69
- Afzuiging van stof en spanen 69
- Ingebruikneming 70
- Onderhoud en service 71
- Afvalverwijdering 72
- Generelle advarselshenvisnin 73
- Værktøjsspecifikke 75
- Funktionsbeskrivelse 76
- Montering 77
- Værktøjsskift 78
- Støv-/spånudsugning 78
- Ibrugtagning 78
- Vedligeholdelse og service 79
- Bortskaffelse 80
- Verktygsspecifika 83
- Funktionsbeskrivning 84
- Försäkran om överensstämmelse 85
- Verktygsbyte 86
- Damm-/spånutsugning 86
- Driftstart 86
- Underhåll och service 87
- Kundservice och kundkonsulter 88
- Avfallshantering 88
- ADVARSEL 89
- Maskinavhengig sikkerhets 91
- Funksjonsbeskrivelse 92
- Verktøyskifte 94
- Støv-/sponavsuging 94
- Igangsetting 94
- Service og vedlikehold 95
- Deponering 96
- VAROITUS 97
- Laitekohtaiset turvallisuus 99
- Toimintaselostus 100
- Standardinmukaisuusvakuutus 101
- Akun lataus (katso kuva A) 101
- Työkalunvaihto 102
- Pölyn ja lastun poistoimu 102
- Käyttöönotto 102
- Hoito ja huolto 103
- Kuljetus 104
- Γενικές προειδοποιητικές 105
- Ειδικές ως προς το μηχάνημα 107
- Φορτιστής μπαταριών 108
- Περιγραφή λειτουργίας 109
- Συναρμολόγηση 110
- Αντικατάσταση εξαρτήματος 111
- Λειτουργία 112
- Συντήρηση και Service 113
- Μεταφορά 114
- Απόσυρση 114
- Uyar Talimat 115
- Alete özgü güvenlik talimat 117
- Fonksiyon tanm 118
- Uygunluk beyan 119
- Uç değiştirme 120
- Toz ve talaş emme 120
- Çalştrma 120
- Bakm ve servis 121
- SDS-Quick 123
Related products and manuals for Cordless rotary hammers Bosch Uneo
(196 pages)
© 2020, manymanuals.com. All rights reserved. | 0.509 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals