Bosch DRC97AQ50 Installation Manual download pdf (Page 9)

Operating the appliance en

Sensor control

In automatic mode, a sensor in the extractor hood

detects the intensity of the cooking and roasting

odours. Depending on the sensor setting, the fan

automatically switches itself to another fan setting.

Possible sensor settings:

Default sensitivity setting: LED 3 (fan setting 3)

Lowest sensitivity setting: LED 1 (fan setting 1)

Highest sensitivity setting: LED 5 (intensive mode 2)

If the sensor control responds too strongly or not

enough, it can be changed accordingly:

1. When the appliance is switched off, press and hold

the # and w buttons for approx. 3 seconds.

2. Press the @ or A button to change the sensor control

setting.

3. Press and hold the # and w buttons for

approx. 3 seconds to save the setting or wait for

approx. 10 seconds until the setting is automatically

saved.

A signal tone will sound.

Note: Press the # button to cancel the setting.

Saturation display

When the metal grease filters or the air recirculation

filter are saturated after the appliance has been

switched off, the corresponding symbols flash and a

repeated signal tone sounds:

■ Metal grease filter: LED 1 flashes

■ Air recirculation filter: LED 2 flashes

■ Metal grease filter and air recirculation filter: LEDs

1 and 2 flash

If you have not yet done so, the metal grease filters

should now be cleaned or the air recirculation filter

replaced. ~ "Cleaning and maintenance" on page 13

The saturation indicators can be reset while they are

flashing. To do this, press the y button.

Switching over to circulating-air mode

For circulating-air mode, the electronic controller must

be switched over accordingly.

1. When the appliance is switched off, press and hold

the # and y buttons for approx. 3 seconds.

The LED for the currently active filter setting lights up

on the appliance.

2. Press the @ button/A button until LED 2 for

circulating-air mode (filter cannot be regenerated)

lights up on the appliance.

3. Press the @ button/ A button until LED 3 for

circulating-air mode (filter can be regenerated) lights

up on the appliance.

4. Press the @ button/A button until LED 1 on the

appliance for the electronic controller is switched

back to operation without air recirculation filter.

5. Press and hold the # and y buttons for

approx. 3 seconds to save the setting or wait for

approx. 10 seconds until the setting is automatically

saved.

A signal tone will sound.

Note: Press the # button to cancel the setting.

Lighting

The lighting can be switched on and off independently

of the fan.

Press the B button.

Setting the brightness

Press and hold the x or } button until the required

brightness is reached.

Note: Colour temperature settings are available in the

Home Connect app provided the appliance has this

function.

Button tone

Switching on or off

Note: Only button tones can be switched on and off.

Signal tones on the appliance cannot be switched off.

1. When the appliance is switched off, press and hold

the # and A buttons for approx. 3 seconds.

The LED in the currently selected setting lights up.

2. Press the @ or A button to change the setting.

The button tones are switched on if LED 1 lights up

on the appliance.

The button tones are switched off if LED 2 lights up

on the appliance.

3. Press and hold the # and A buttons for

approx. 3 seconds to save the setting or wait for

approx. 10 seconds until the setting is automatically

saved.

A signal tone will sound.

Note: Press the # button to cancel the setting.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 23 24

Comments to this Manuals

No comments

Bosch DRC97AQ50 Installation Manual Page 9

Comments to this Manuals

Related products and manuals for Fireplaces Bosch DRC97AQ50