Bosch PLH181 Specifications download pdf (Page 10)

'%%#"#&*'

<91 A52 A<<9 D6A5 /<A5

5.;1@D5692@A.?A6;4 A52

A<<9 @6;02 A<?>B2 3?<: A52:<A<? 0.;

0.B@2A52A<<9A<AD6@A

To turn tool "ON", depress the "Lock-OFF"

button and squeeze the trigger switch. To turn

the tool "OFF", release the trigger switch which

is spring loaded and will return to "OFF"

position automatically.

To increase switch life, do not turn switch on

and off while tool and drum are held against a

workpiece.

%

When the trigger is released it activates the

electrical brake to stop the blade quickly. This

feature is especially useful when making

repetitive cuts.

$ ""'#"

Check that the workpiece is held in place

securely on your work surface. Stand

comfortably, hold the planer firmly with both

hands. With the planer fully adjusted, place

the front shoe on the workpiece, (be certain

that the cutter drum is not in contact with the

work) and start the planer. With pressure on

the front shoe, and the fence against the side

of the work (to control the width or angle) feed

the planer steadily until the rear shoe fully

engages the workpiece. Gradually transfer

pressure to the rear shoe and continue planing

to the end of the cut. Feed the planer at a

uniform and reasonable rate, which does not

put excessive strain on the motor or blades.

Do not pull the planer back over the surface

already cut. Use progressive cuts until you are

near the desired depth, and then re-adjust to a

light cut for the final pass to obtain a good

surface finish.

'52 :<A<? :.F @A.99 63

6:=?<=2?9F B@21 <?

<C2?9<.121 Reduce the pressure (feed rate)

or depth of cut to prevent possible damage to

the tool if the motor labors.

&'"%("

The guide fence can be used to control the

width of the cut or for simply providing added

stability and protection when cutting materials

that are up to 3-1/4" wide.

"<A2 When used for rabbeting, the fence

must be attached to the left side of the tool.

(Fig. 1).

Installing the guide fence: Place the wing knob

through the appropriate hole in the guide

bracket and screw into preferred side of the

housing. Securely tighten wing knob. Setting

the cutting width: Place wing knob through the

appropriate fence arm and slide along the

guide bracket to the desired position. Securely

tighten wing knob. Be certain that the flat

washer (supplied) is fitted between the bottom

of the guide fence and wing knob or the guide

fence is likely to slip.

 (+("

The deluxe guide fence can be used to control

the width of the cut or for simply providing

added stability and protection when cutting

materials that are up to 3-1/4" wide, with the

additional capability of guiding the planer on

any angle up to 45 degrees, to allow edge

chamfering and beveling (Fig. 7).

-10-

#=2?.A6;4;@A?B0A6<;@

(&'"$'#('

Proper cutting depth should be determined

according to the hardness, gumminess or

moisture content of the material being cut, as

well as the feed rate, and is largely a matter of

experience. Start with a light cut and increase

the depth setting if the planer moves freely

through the workpiece with no excessive load

on the motor. Do not change depth of cut

while planing.

The cutting depth is determined by the

difference in height between the adjustable

front shoe, and the fixed rear shoe of the

planer. As the front shoe is adjusted, it retracts

and exposes the blade, which can then

remove the desired amount from the

workpiece. The cutting depth is graduated

from 0 to 1/16 of an inch, and the "0" indicates

the blade is fully retracted.

Adjusting depth of cut: Rotate depth

adjustment knob until the indicator engages

the detent which indicates the desired cutting

depth on the depth scale (Fig. 1).

The planer may be set to cut any depth from 0

to 1/16 of an inch.

$#%'& '#% )%

Moving the port selector lever to position 1

(towards front of tool) discharges chips to the

left, while position 2 (towards rear of tool)

discharges chips to the right (Fig. 1)

CAUTION

WARNING

BM 2610020981 05-12_2610020981 05-12.qxp 5/3/12 9:12 AM Page 10

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 47 48

Comments to this Manuals

No comments

Bosch PLH181 Specifications Page 10

Comments to this Manuals