Bosch GOF 1300 CE Professional Operations Instructions download pdf (Page 27)

English | 27

Bosch Power Tools 1 609 929 N93 | (2.9.08)

Coarsely adjust the required radius by moving

the router compass and tighten the wing bolts

38 and 39.

The length can be fine adjusted with the fine-ad-

justment knob 40 after loosening the wing bolt

39. One revolution corresponds with a setting

range of 2.0 mm. One graduation mark on the

fine-adjustment knob 40 changes the setting

range by 0.1 mm.

Guide the switched on power tool over the

workpiece with the right handle 1 and the router

compass handle 37.

Routing with Guide Rail (see figure I)

Straight routing cuts can be carried out with

help of the guide rail 43.

The base spacer 42 must be mounted in order to

compensate the height difference.

Mount the router compass/guide-rail adapter 36

as shown in the figure.

Fasten the guide rail 43 to the workpiece with

suitable clamping devices, e. g. screw clamps.

Place the machine with the guide-rail adapter 36

mounted onto the guide rail.

Routing with Guide Bushing (see figures K–N)

The guide bushing 47 enables template and pat-

tern routing on workpieces.

In order to use the guide bushing 47, the guide

bushing adapter 44 must be inserted into the

guide plate 9 first.

Place the guide bushing adapter 44 from above

onto the guide plate 9 and tighten it firmly with

the 2 fastening screws 45. Pay attention that

the release lever for the guide bushing adapter

46 is freely movable.

Choose a suitable guide bushing, depending on

the thickness of the template or the pattern. Be-

cause of the projecting height of the guide bush-

ing, the template must have a minimum thick-

ness of 8 mm.

Actuate the release lever 46 and insert the guide

bushing 47 from below into the guide bushing

adapter 44. Ensure that the encoding keys clear-

ly engage in the grooves of the guide bushing.

f Select a router bit with a diameter smaller

than the interior diameter of the guide

bushing.

To ensure that the distance from router bit cen-

tre and guide bushing edge is uniform, the guide

bushing and the guide plate can be adjusted to

each other, if required.

– Push the release lever 22 down and guide the

router to the stop in the direction of the base

plate 12. Let go of the release lever 22

again,

in order to lock this plunging depth.

– Unscrew the countersunk head screws 49.

Screw the pan head screws 48 into the holes

intended for this purpose in such a manner

that the guide plate 9 can be moved freely.

– Insert the centring pin 50 into the tool holder

as shown in the figure. Hand-tighten the

tightening nut so that the centring pin can

still be moved freely.

– Align the centring pin 50 and the guide bush-

ing 47 to each other by slightly moving the

guide plate 9.

– Tighten the pan head screws 48.

– Remove the centring pin 50 from the tool

holder.

– Push the release lever 22 and guide the

plunge router to the uppermost position.

For routing with the guide bushing 47 proceed

as follows:

– Guide the switched on power tool with the

guide bushing toward the template.

– Push the release lever 22 down and slowly

lower the plunge router until the adjusted

depth-of-cut is reached. Let go of the release

lever 22 again to lock this cutting depth.

– Guide the switched on power tool with the

protruding guide bushing alongside the tem-

plate applying lateral pressure.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

OBJ_BUCH-203-003.book Page 27 Tuesday, September 2, 2008 8:46 AM

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 296 297

Comments to this Manuals

No comments

Bosch GOF 1300 CE Professional Operations Instructions Page 27

Comments to this Manuals