Bosch X10 User Manual Page 20
- Page / 132
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
20 en | Installation VideoJet X10
V3.0 | 2007.09 Installation and Operating Manual Bosch Security Systems
4.3 Connections
4.3.1 Camera
You can connect a video source to the VideoJet X10. Any cameras and other video sources
that produce a standard PAL or NTSC signal are suitable.
1. Connect the camera or another video source to the BNC Video In socket using a video
cable (75 Ohm, BNC plug).
2. If the video signal is not looped through, termination is performed by a software setting if
necessary (see Abschnitt 5.13 Video Input, Seite 43).
4.3.2 Audio Connections
The VideoJet X10 has two audio ports for audio line signals.
The audio signals are transmitted two-way and in sync with the video signals. As a result, you
can connect a speaker or door intercom system at the destination point, for example. The
following specifications should be complied with in all cases.
The stereo plugs must be connected as follows:
1. Connect an audio source with line level to the Audio In socket of the VideoJet X10 with a
3.5 mm stereo plug.
2. Connect a unit with line-in connection to the Audio Out socket of the VideoJet X10 with a
3.5 mm stereo plug.
4.3.3 Network
You can connect the VideoJet X10 to a 10/100 Base-T network using a standard UTP
category 5 cable with RJ45 plugs. The second Ethernet interface can be used to create a
redundant connection to the network.
1. Connect the VideoJet X10 to the network via the ETH 1 socket.
2. Connect the VideoJet X10 to a redundant switch or hub on the same network via the
ETH 2 socket.
1 × Line In: Impedance 9 kOhm typ., 5.5 V
p-p
max. input voltage
1 × Line Out: Impedance 10 kOhm typ., 3.0 V
p-p
max. output voltage,
impedance 16 Ohm min., 1.7 V
p-p
max. output voltage
Contact Line In function Line Out function
Tip Channel 1 (camera 1) Channel 1 (camera 1)
Middle ring – –
Lower ring Ground Ground
i
NOTICE!
You cannot create a connection to a second network.
- VideoJet X10 1
- Table of Contents 3
- 10 Specifications 125 5
- 10.1 Unit 125 5
- 10.2 Protocols/Standards 126 5
- 11 Index 127 5
- 1Preface 7
- 1.4 EU Directives 8
- 1.5 Rating Plate 8
- 2Safety Information 9
- 3 Product Description 11
- 3.2 System Requirements 12
- 3.3 Overview of Functions 13
- 3.3.13 Summary 15
- 4 Installation 19
- 4.3 Connections 20
- 4.3.4 SFP Slot 21
- 4.3.5 Direct iSCSI Connection 21
- 4.3.6 CF Slot 21
- 4.3.7 Data Interface 22
- 4.3.8 Alarm Inputs 22
- 4.3.9 Relay Outputs 23
- 4.3.11 Backup Power Supply 24
- 4.4 Power On/Power Off 25
- 4.5.3 Reboot 26
- 4.5.4 Additional Parameters 26
- 5.1 Connecting 27
- 5.2 Configuration Menu 29
- 5.2.1 Starting Configuration 30
- 5.2.2 Navigation 30
- 5.2.3 Making Changes 30
- 5.3 Identification 31
- 5.4 Camera Name 31
- 5.5 Display Stamping 32
- 5.5.4 Alarm message 33
- 5.5.5 Video watermarking 33
- 5.6 Password 34
- 5.7 Language 35
- 5.8 Date/Time 35
- 5.9 Time Server 35
- 5.9.1 Unit time zone 36
- 5.9.2 Daylight saving time 36
- 5.9.3 Time server IP address 36
- 5.9.4 Time server type 36
- 5.10 Picture Settings 37
- 5.11 Encoder Profile 38
- 5.11.1 Active profile 39
- 5.11.2 Preview for 39
- 5.12 Profile Configuration 40
- 5.12.8 I-frame distance 42
- 5.12.9 P-frame quality 42
- 5.12.10 I-frame quality 42
- 5.13 Video Input 43
- 5.14 Audio 44
- 5.15 JPEG Posting 45
- 5.15.3 Posting interval 46
- 5.15.4 FTP server IP address 46
- 5.15.5 FTP server login 46
- 5.15.6 FTP server password 46
- 5.15.7 Path on FTP server 46
- 5.16 Storage Medium 47
- 5.17 iSCSI 48
- 5.17.10 Storage Information 50
- 5.18 Partitioning 51
- 5.18.1 Creating a Partition 52
- 5.18.2 Saving Changes 53
- 5.18.3 Partition status 53
- 5.18.6 Partition number 54
- 5.18.4 Editing a Partition 54
- 5.18.5 Partition name 54
- 5.18.7 Type of recording 55
- 5.18.8 Number of alarm tracks 55
- 5.18.9 Alarm track size 55
- 5.18.10 Format 56
- 5.19 Recording Profiles 57
- 5.20 Recording Scheduler 59
- 5.20.1 Holidays 60
- 5.20.2 Deleting Holidays 60
- 5.20.3 Time Periods 60
- 5.20.5 Recording status 60
- 5.21 Alarm Sources 61
- 5.22 Alarm Connections 62
- 5.22.4 Destination password 63
- 5.22.5 Video transmission 63
- 5.22.6 Remote port 63
- 5.22.7 Video output 63
- 5.22.8 Decoder 63
- 5.22.9 SSL encryption 64
- 5.22.10 Auto-connect 64
- 5.22.11 Audio 64
- 5.23 VCA 65
- 5.23.1 Analysis 66
- 5.23.2 Analysis type 66
- 5.23.13 Scene too noisy 69
- 5.23.14 Global change 69
- 5.23.15 Reference check 69
- 5.23.16 Select area 69
- 5.24 Alarm E-Mail 70
- 5.24.7 Destination address 71
- 5.24.8 Sender name 71
- 5.24.9 Test e-mail 71
- 5.25 Alarm Task Editor 72
- 5.26 Relay Settings 73
- 5.26.3 Relay follows 74
- 5.26.4 Relay name 74
- 5.26.5 Trigger relay 74
- 5.27 COM1 75
- 5.28 Network 77
- 5.29 Multicasting 81
- 5.29.2 Port 82
- 5.29.3 Streaming 82
- 5.29.4 Multicast packet TTL 82
- 5.30 Encryption 83
- 5.30.1 Encryption 84
- 5.31 Version Information 85
- 5.32 Livepage Configuration 86
- 5.33 System State 89
- 5.34 Licenses 90
- 5.35 Maintenance 91
- 5.35.2 Configuration 92
- 5.35.3 SSL certificate 92
- 5.35.4 Maintenance log 92
- 5.36 Function Test 93
- 6 Operation 95
- 1. Start the Web browser 96
- 6.2 The LIVEPAGE 97
- 6.2.4 View Control 98
- 6.2.5 Digital I/O 98
- 6.2.6 Trigger Relay 98
- 6.2.7 System Log / Event Log 99
- 6.2.8 Audio Function 99
- 6.3 Saving Snapshots 100
- 6.4 Recording Video Sequences 100
- 6.5 Running Recording Program 100
- 6.6 The RECORDINGS Page 101
- 6.6.2 Controlling a Playback 102
- 6.6.3 Buttons 102
- 6.6.4 Slide Control 103
- 6.6.5 Bookmarks 103
- 6.7 Backup 104
- 6.8 Installing the Player 105
- 6.9.1 Installation 106
- 6.9.2 Connecting 106
- 6.9.3 Connecting on Alarm 106
- 7 Maintenance and Upgrades 109
- 7.3 Repairs 110
- 7.4 Transfer and Disposal 110
- 8 Appendix 111
- 8.2 General Malfunctions 112
- 8.4 LEDs 115
- 8.5 Processor Load 116
- 8.6 Serial Interface 116
- 8.7 Terminal Block 117
- 8.8.1 Data Terminal 118
- 8.8.3 Command Inputs 118
- 8.8.4 Assigning an IP Address 119
- 8.8.5 Reboot 119
- 8.8.6 Additional Parameters 119
- 9Glossary 121
- 10 Specifications 125
- 10.2 Protocols/Standards 126
- 11 Index 127
- 128 en 128
- VideoJet X10 Index 129
- 130 en 130
Related products and manuals for Software Bosch X10
Software Bosch MBV-BPRO-40 Operator's Manual
(220 pages)
(220 pages)
Software Bosch 430 Specifications
(17 pages)
(17 pages)
Software Bosch BIS V3.0 User Manual
(8 pages)
(8 pages)
Software Bosch IVA 4.0 User Manual
(4 pages)
(4 pages)
Software Bosch PRS‑SWCS User Manual
(3 pages)
(3 pages)
Software Bosch VP-CFGSFT User Manual
(3 pages)
(3 pages)
© 2020, manymanuals.com. All rights reserved. | 0.242 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals