Bosch DHD865AUC Specifications download pdf (Page 4)

INSTALL DUCTWORK

CAUTION oBEFORE CUTTING HOLE tN CABINET FOR DUCT-

WORK: Check for interference with floor joists, wall studs, electri-

cal wiring or plumbing.

3-1/4" X 10"

TO 6" RD

TRANSITION

UP ! DOWN ooo Raises and lowers vent.

Turns blower ON when vent is UP and OFF when

vent is DOWN.

DELAY ......... Allows blower to run for 5 min. after button is

pressed. Blower will run for 5 min. - then shut

OFF. VENT WILL NOTLOWER. You must press

UP / DOWN to lower vent.

LOW / MED ! HGH ..... Operates blower at 3 different speed

levels. Press button ONCE to turn blower

ON to desired speed. Press button

AGAIN to turn blower OFF.

FILTER LIGHT ........... Comes ON after 30 hours of operation

to remind you to clean filters. Press

button to reset.

6" RD.

ELBOW &

DUCT-

1. Cut hole in cabinet as well as holes in wall or floor as

necessary.

2. Mount the roof or wall cap and work back towards the cabinet,

attaching all ductwork, elbows and transitions as previously

planned. Tape all ductwork connections to make them secure

and air tight.

3. Connect ductwork (and transition, if required) to downdraft. If

necessary, LOOSEN nuts and screws that hold the blower in

place, and slide blower left or right to meet ductwork. Re-

tighten screws and nuts.

Note: A 3-1/4" x 10" collar is provided for installers who prefer to

rivet the ductwork to the unit. This wil! allow blower to be removed

and replaced easily in service situations without disturbing

ductwork.

INSTALL ELECTRICAL WIRING

1. Mount a standard wiring box, with 3-pronged receptacle,

inside the cabinet. Make sure the downdraft's power cord can

easily reach it.

2. Run appropriate power cable into cabinet and connect it to

receptacle.

3. Plug the downdraft's power cord into the outlet.

INSTALL COOKTOP

1. Align the cooktop with the downdraft and fasten cooktop in

place.

Note: Accurate alignment of cooktop and downdraft is necessary

to ensure that there is no interference when air vent is raised and

lowered. There should be a gap of 1/32"ol/16" between the back

of the cooktop and the front of the downdraft cover.

OP'TIONAL DOOR KITS

MODEL NO. DESCRIPTION

DHZ8020 30" White

DHZ8O6O 30" Black

DHZ9O2O 36" White

DHZ9O6O 36"Black

USE AND CARE

WARNING: A_ways disconnect e_ectric

power supply before cleaning unit.

Use a mild detergent suitable for painted surfaces. DO NOT USE

ABRASIVE CLOTH, STEEL WOOL PADS, OR SCOURING

POWDERS. Vacuum blower to clean. Do not immerse blower in

water.

Wash the 2 aluminum/stainless steel grease filters in a mild

detergent solution or a dishwasher. Remove them from the air

vent by grasping the tab at the top of each filter.

SERViCiNG

WARNING: A_ways disconnect e_ectric

power supply before servicing unit.

It may be necessary to remove the downdraft blower system from

the cabinet in order to service components such as the blower

motor or air vent mechanism.

Disconnect power to the cooktop and remove it first. Reverse the

steps under "MOUNT THE UNIT" to remove the downdraft from

the cabinet.

1 2 3 4 5 6 7 8 9 ... 15 16

Comments to this Manuals

No comments

Bosch DHD865AUC Specifications Page 4

Comments to this Manuals

Related products and manuals for Air blowers/dryers Bosch DHD865AUC