Bosch 4412 User Manual download pdf

Control Panel D4412

Release Notes July 2003

Affects: Firmware Revision 1.08

1.0 Compatibility

1.1 D6600 Communications

Receiver/Gateway

When programmed to communicate in the Modem

IIIa

Format, the D4412 control panel must report to a

D6600 with a Central Processing Unit (CPU) running

revision 01.01.03 firmware or later.

1.2 D6500 Central Station Receiver

When programmed to communicate in the Modem

IIIa

Format, the D4412 control panel must report to a

D6500 with a D6511 Main Processing Unit (MPU)

running revision 1.05 firmware or later. The D6500

with a D6510 MPU does not support Modem IIIa

Format.

1.3 RPS (RAM IV)

To program a D4412 from a remote location, you

must use the Remote Programming Software (RPS/

RAM IV) version 3.6 or greater.

2.0 Version 1.08 Supports new

‘Hybrid Telephone Circuit’

• Control panel/RPS Communication Issue:

control panels shipped from the factory with

firmware revision less than 1.08 may have

difficulty communicating with RPS (RAM IV) in

some less than optimal telephone environments.

The D6412/D4412 Control Panel/RPS (RAM IV)

Technical Service Note (P/N: 4998122763) explains

the issue in detail. It includes complete

instructions for diagnosis and offers several

remedies.

• No issue for control panels shipped with

Version 108 Firmware: control panels shipped

from the factory with Version 1.08 firmware are

fitted with a new ‘Hybrid Telephone Circuit’. This

new circuit in combination with firmware revision

1.08 resolves the control panel/RPS

communication issue.

Upgrading the control panel firmware to

revision 1.08 in those control panels with

an older Hybrid Telephone Circuit may

slightly improve the control panel’s noise

filtering capability. In some less than

optimal telephone environments this slight

improvement may address a control

panel/RPS communication issue. However,

if the control panel shows any symptoms of

a control panel/RPS communication issue,

Bosch strongly recommends that you

follow the diagnostic procedure outlined in

the D6412/D4412 Control Panel/RPS

(RAM IV) Technical Service Note

(P/N: 4998122763). You can find the

Technogram at our web site or contact

tech support at (888) 886-6189 to order a

copy.

3.0 Known Issues in Firmware

Version 1.08

• Cmd 54 Does Not Activate ‘Pulse Mode’

Outputs: Cmd 54 does not activate outputs

programmed for ‘Pulse Mode’.

• Sensor Trouble Monitor Output activates

when Controlled Point is faulted: Internal

testing has found that when a trouble condition

occurs on a controlled point (Entry/Exit Delay 1

or 2, Follower, Instant), an output programmed

for Sensor Trouble Monitor activates. The output

programmed for this function should only activate

when the number of days entered for Sensor

Monitor Time passes without any sensor (point)

activity.

• Second Pulse on Cross Point does not create

Alarm Condition: Internal testing has found that

a second pulse on a Cross Point that lasts 20

seconds or longer does not create an alarm

condition for that point.

• Unverified Event Report: The D4412 sends the

incorrect Cross Group Number (Point Index

Number) when there is a fault on only one point.

A fault on only one point in a Cross Group is

defined as an unverified event.

1 2 3 4

Control Panel D4412 1

Summary of Contents

Page 1 - Control Panel D4412

Control Panel D4412Release Notes July 2003Affects: Firmware Revision 1.081.0 Compatibility1.1 D6600 CommunicationsReceiver/GatewayWhen programmed to c

Page 2

Page 3

Page 4

Bosch 4412 User Manual

Browse online or download User Manual for Circular saws Bosch 4412. D4412 Release Notes

Summary of Contents

More documents for Circular saws Bosch 4412

Comments to this Manuals

Bosch 4412 User Manual

Browse online or download User Manual for Circular saws Bosch 4412. D4412 Release Notes

Summary of Contents

More documents for Circular saws Bosch 4412

Comments to this Manuals

Related products and manuals for Circular saws Bosch 4412