Bosch Uneo Operations Instructions download pdf (Page 10)

10 | English

2 609 006 431 | (2.4.13) Bosch Power Tools

 Maintain power tools. Check for misalignment or bind-

ing of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power

tools.

 Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

 Use the power tool, accessories and tool bits etc. in ac-

cordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

Battery tool use and care

 Recharge only with the charger specified by the manu-

facturer. A charger that is suitable for one type of battery

pack may create a risk of fire when used with another bat-

tery pack.

 Use power tools only with specifically designated bat-

tery packs. Use of any other battery packs may create a

risk of injury and fire.

 When battery pack is not in use, keep it away from oth-

er metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

 Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally oc-

curs, flush with water. If liquid contacts eyes, addition-

ally seek medical help. Liquid ejected from the battery

may cause irritation or burns.

Service

 Have your power tool serviced by a qualified repair per-

son using only identical replacement parts. This will en-

sure that the safety of the power tool is maintained.

Hammer Safety Warnings

 Wear ear protectors. Exposure to noise can cause hear-

ing loss.

 Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory

or fastener may contact hidden wiring. Cutting accesso-

ry and fasteners contacting a “live” wire may make ex-

posed metal parts of the power tool “live” and could give

the operator an electric shock.

Additional Safety and Working In-

structions

 When transporting and storing, set the rotational di-

rection switch to the centre position. Danger of injury

when accidentally actuating the On/Off switch.

 Use appropriate detectors to determine if utility lines

are hidden in the work area or call the local utility com-

pany for assistance. Contact with electric lines can lead

to fire and electric shock. Damaging a gas line can lead to

explosion. Penetrating a water line causes property dam-

age.

 When working with the machine, always hold it firmly

with both hands and provide for a secure stance. The

power tool is guided more secure with both hands.

 Secure the workpiece. A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.

 For drilling without impact in wood, metal, ceramic and

plastic, a suitable SDS-Quick tool or an application tool

with hexagon shank can be used.

 Inserting SDS-Quick Drilling Tools: Check the latching by

pulling the tool.

 The maximum torque is reached only in the screwdriving

operating mode (1. gear). The maximum no-load speed is

reached only in the operating modes drilling and hammer

drilling.

 Replace a damaged dust protection cap immediately.

The dust protection cap largely prevents the penetration of

drilling dust into the tool holder during operation. When in-

serting the tool, pay attention that the dust protection cap

is not damaged.

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health and cause allergic reactions, lead to res-

piratory infections and/or cancer. Materials containing

asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suita-

ble for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

 If the application tool should become blocked, switch

the machine off. Loosen the application tool.

 When switching on with a blocked drilling tool, high

torque reaction can occur.

 Apply the power tool to the screw only when it is

switched off. Rotating tool inserts can slip off.

 Always wait until the machine has come to a complete

stop before placing it down. The tool insert can jam and

lead to loss of control over the power tool.

 To save energy, only switch the power tool on when using

it.

 Avoid unintentional switching on. Ensure the On/Off

switch is in the off position before inserting battery

pack. Carrying the power tool with your finger on the

On/Off switch or inserting the battery pack into power

tools that have the switch on invites accidents.

 Do not open the battery. Danger of short-circuiting.

OBJ_BUCH-1695-002.book Page 10 Tuesday, April 2, 2013 10:59 AM

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 94 95

Comments to this Manuals

No comments

Bosch Uneo Operations Instructions Page 10

Comments to this Manuals

Related products and manuals for Cordless combi drills Bosch Uneo