Bosch D9210C User Manual download pdf (Page 4)

GV4 Series Control Panel | Release Notes

4 Bosch Security Systems, Inc. | 11/11 | F01U261045-01

Cycl

e Relay, Cycle Door (Door Access and

Control), and Auto Re-arm.

Dual Authentication

 Dual authentication requ

ires a user to present

both a credential to a D9210C door

controller, and a passcode to be entered at

an associated keypad.

 Dual authentication requires the passcode

and credential of the same user to be

presented within the time duration set in

Command Center>Dual Authentication

Duration.

Arm/Disarm

 The Arm/Disarm function changes a

authorized areas in scope from disarm to

master armed, or from any armed state to

disarmed when Passcode and [ENT] is

pressed.

 The control panel shall only arm areas where

the user has L# Passcode Arm authority

enabled and shall only disarm areas where

the user has L# Passcode Disarm authority.

Cycle Relay

 The Cycles Relay comm

and momentarily

activates a preconfigured output when

Passcode and [ENT] are pressed.

 A user

must have a non-zero authority level in

the keypads current area to perform the Cycle

Relay Function.

Cycle Door (Door Access and Control)

 The Cycle D

oor Command was enhanced to

perform all functions associated with Door

Access. After a user is authenticated, the door

cycles the striker, the current area disarms,

and then a custom function executes.

Auto Re-arm Features

 The Auto

Re-arm function is intended to be

used on a keypad with area-wide scope to

provide a facility with the ability to

temporarily disarm the perimeter before

automatically re-arming.

 This keypad is assigned to an area that

contains a perimeter delay point. The user

can exit the facility through this point.

 The Auto-Re-arm function automatically

restarts the exit delay for Master Arm if the

authenticating user has L# Passcode Arm

authority and the keypads current area is

already armed at any state.

2.1.4 Number of Users

 Previous G

Series control panels delivered

249 passcodes and 996 credentials using a

User and Sub-User method. GV4 Series

control panels support a total of 1000 unique

users, whereby ì User 0î is the installer. Each

system user now supports a Passcode,

Credential, and Keyfob so that user activity is

unique and detailed.

 The D9412GV4 can support up to 1000 users.

 The D7412GV4 can support up to 400 users.

 The D7212GV4 can support up to 100 users.

 Standard Users are numbered from 1 to 999.

 Any control panel user can be configured via

the keypad using Command 5-6, or through

the use of RPS.

 All standard D9412GV4 and D7412GV4 users

can have an access credentials assigned with

individual authority permissions. Sub-Users

are not supported.

 All standard users can be assigned a wireless

keyfob through RF Diagnostics or Command

56 on a keypad or through RPS.

If RPS is used to add, replace, or remove

any keyfobs, no keyfob-specific events will

be generated. Only the Parameters

Changed event will be logged.

2.1.5 SDI2 Support

The GV4 series control panel support two

independent SDI busses on the main control

panel. The SDI2 bus does not support SDI

devices.

SDI2 Module Supervision

 When a

n SDI2 device fails supervision, a

system fault is annunciated at the keypads

indicating the individual device number.

 When a SDI2 bus Octo-input module, or an RF

Receiver module is declared missing, then all

points associated with those devices will also

be declared missing.

SDI2 Module Tamper

 Most S

DI2 bus devices have an optional

tamper input to detect when the cover is

opened or when the device is removed from

its mount.

 Module tamper conditions reported by SDI2

bus modules will be annunciated on the

keypads as a system fault and optionally sent

to the central station as an event.

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

Bosch D9210C User Manual Page 4

Comments to this Manuals

Related products and manuals for Networking Bosch D9210C