Bosch ICP-CC404 Installation Guide download pdf (Page 27)

ICP-CC404 | Installation Guide | 6.0 System Functions

Bosch Security Systems, Inc. | 12/08 | F01U089401-02 27

If horn speaker indication beeps are enabled, one

beep sounds from the horn speaker. If strobe

indications are enabled, the strobe flashes for 3 sec to

indicate the system is disarmed.

5.5.5 Panic Alarm

Press and hold both [AWAY] and [STAY] together

for 2 sec.

An audible Panic Alarm is initiated that activates the

horn speaker, strobe, and internal sirens.

If Option 1 is selected in Location 425

(refer to Section 18.2 System Options 2

on page 73), the remote radio Panic

Alarm is also silent.

5.5.6 Remote Outputs

The [DOOR] and [AUX] buttons on the four-channel

hand-held transmitter can operate two remote

outputs. Only the installer can program these outputs.

You can use the Output Event Types listed in

Table 18. Refer Section 16.0 Programmable Outputs for

more information.

Table 18: Remote Output Event Types

Output

Event Type Description Page

2,11 Radio Control Output 1 67

2,12 Radio Control Output 2 67

2,13 Radio Control Output 1 – not

armed in AWAY Mode

2,14 Radio Control Output 2 – not

armed in AWAY Mode

To turn Output 1 on:

Press and hold [DOOR] for 2 sec.

Output 1 turns on.

To turn Output 1 off:

Press and hold [DOOR] for 2 sec.

Output 1 turns off.

To turn Output 2 on:

Press and hold [AUX] for 2 sec.

Output 2 turns on.

To turn Output 2 off:

Press and hold [AUX] for 2 sec.

Output 2 turns off.

All reset times for the [DOOR] and

[AUX] buttons are referenced to

Polarities 1 and 8. Reset times vary

depending on the polarity used.

6.0 System Functions

This section explains more advanced features, such as

Installer Code, Master Code, and hold-down

functions used for testing and regular maintenance of

the system.

6.1 Installer Code Functions

Installer Code functions allow the installer to perform

various system tests and tasks without knowing a

Master Code.

To access the required Installer Code function, enter

the Installer Code and corresponding function digit,

and press [AWAY]. The Installer Code functions are

listed in Table 19.

You can only access these functions when the system

is disarmed.

Table 19: Installer Code Functions

Function Description

0 Reserved

1 Set the number of days until the first Test

Report

(Section 6.1.1)

2 Change domestic telephone numbers

(Section 6.1.2)

3 Change the Telco arming or disarming

sequence

(Section 6.1.3 on page 28)

4 Setting STAY Mode 2 zones

(Section 6.1.4 on page 30)

5 Satellite Siren (EDMSAT) Service Mode

(Section 6.1.5 on page 30)

6 Turn Telephone Monitor Mode on and off

(Section 6.1.6 on page 31)

7 Walk Test Mode

(Section 6.1.7 on page 31)

8 Event Memory Recall Mode

(Section 6.1.8 on page 31)

9 Reserved

6.1.1 Set the Number of Days until the First Test

Report

This function determines when the system sends the

first Test Report (Contact ID Event Code 602). If you

do not use this Installer Code Function, the first Test

Report is sent to the base station receiver after the

repeat interval programmed in Location 366 (refer to

Section 15.21 Test Reporting Time on page 63). If you

want the system to send the first Test Report sooner

than the repeat interval, use this function to set when

the first Test Report is sent.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 97 98

Comments to this Manuals

No comments

Bosch ICP-CC404 Installation Guide Page 27

Comments to this Manuals

Related products and manuals for Security access control systems Bosch ICP-CC404