Bosch V20-UL Specifications Page 107
- Page / 156
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV4/D7412GV4 v2.03 | Installation and System Reference Guide | 18.0 Installer Menu
.
Bosch Security Systems, Inc. | 4/14 | F01U265457-05
107
4. Delete existing characters, if necessary, and then enter the new number. Use /[PREV] or
/[NEXT] to move through the different bytes.
5. When finished, press the Save softkey to save the programming.
6. When the keypad shows Parameter Saved, escape from the menu.
Default Gateway
B91x/B92x keypads Configuration of Default Gateway
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to the [1] Program > [2] Network > [1] Bus Module (1) or [2] Bus Module (2) > [2] Address
Parameter > [3] Default Gateway menu option.
3. Press [ENTER] to edit the gateway.
4. Delete existing characters, if necessary, and then enter the new number. Use [PREV] or [NEXT]
to move to a different byte.
5. When finished, press [ENTER] to save the programming.
6. When the keypad shows Parameter Saved, escape from the menu.
B93x/B94x keypads Configuration of Default Gateway
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to the [1] Program > [2] Network > [1] Bus Module (1) or [2] Bus Module (2) > [2] Address
Parameter > [3] Default Gateway menu option.
3. Press the Default Gateway softkey to edit the subnet mask address.
4. Delete existing characters, if necessary, and then enter the new number. Use /[PREV] or
/[NEXT] to move through the different bytes.
5. When finished, press the Save softkey to save the programming.
6. When the keypad shows Parameter Saved, escape from the menu.
HTTP Port Number
B91x/B92x keypads Configuration of HTTP Port Number
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to the [1] Program > [2] Network > [1] Bus Module (1) or [2] Bus Module (2) > [2] Address
Parameter > [4] Port Number menu option.
3. Press [ENTER] to edit the port number.
4. Delete existing characters, if necessary, and then enter the new number.
5. When finished, press [ENTER] to save the programming.
6. When the keypad shows Parameter Saved, escape from the menu.
B93x/B94x keypads Configuration of HTTP Port Number
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to the [1] Program > [2] Network > [1] Bus Module (1) or [2] Bus Module (2) > [2] Address
Parameter > [4] Port Number menu option.
3. Press the Port Number softkey to edit the port number.
4. Delete existing characters, if necessary, and then enter the new number.
5. When finished, press the Save softkey to save the programming.
6. When the keypad shows Parameter Saved, escape from the menu.
18.1.6 [2] Network > [1] Bus Module (1) or [2] Bus Module (2) > [3] DNS Parameters
IPv4 Server Address
B91x/B92x keypads Configuration of IPv4 Server Address
1. Enter the installer passcode, and then open the [1] Installer menu.
- Control Panels 1
- Certifications and Approvals 2
- Listings and Approvals 2
- Contents 3
- Figures 6
- 1.0 Introduction 8
- Copyright 9
- Trademarks 9
- 2.0 Lightning Strikes 11
- 3.0 Overview 12
- 3.2 Accessories 14
- 4.0 Installation 21
- 4.5 Connecting Earth Ground 22
- 4.10 Testing the System 24
- 4.11 Service Walk Test 25
- 5.0 Power Supply 28
- 6.0 Power Outputs 34
- 1.4 A − NSC current 35
- Alarm current 35
- 7.0 Telephone Connections 36
- 7.5 Phone LED (Red) 37
- 7.7 Dialing Format 37
- 7.8 Telephone Line Monitor 37
- 7.9 Called Party Disconnect 38
- 7.10 Communication Failure 38
- Phone Cord 39
- D162 2 ft (61 cm) 39
- 8.0 On-Board Points 41
- 8.4 Point Response Time 42
- Using the Rothenbuhler 42
- RED ORG WHT B L K 44
- 9.0 Off-Board Points 45
- 9.4 D8128D OctoPOPIT Module 50
- 9.7 Extra Point Events 57
- 10.0 Off-Board Outputs 59
- 11.0 Arming Devices 64
- 11.4 Keyswitch 66
- Maintained Contact 67
- Momentary Contact 67
- Silencing the Bell 67
- 12.0 SDI Devices 68
- 13.0 SDI2 Devices 71
- Interface 73
- Module 76
- 13.9 B810 wireless receiver 76
- 14.0 Accessory Connector 79
- 15.0 Faceplates 80
- 16.0 Specifications 81
- 16.2 B520 Power Supply 82
- 17.0 Approved Applications 85
- 17.4 Fire Applications 86
- 17.5 Enclosures 94
- 18.0 Installer Menu 95
- 18.1 [1] Program Menu 99
- Area On 112
- Account Number 112
- 18.2 [2] Wireless Menu 125
- 18.3 [3] Diags Menu 130
- 18.4 [4] Srvc Byp Menu 132
- 18.5 [5] Versions Menu 133
- 19.0 UL/NFPA Compliant 134
- Installations 134
- 21.0 Current Ratings Charts 138
- Table 40 140
- 22.2 Bank Safe and Vault 142
- 22.7 UL 609 144
- 22.8 UL 365 144
- 22.9 UL 636 145
- 22.10 ULC S304 Requirements 145
- B.1 Zonex 1 Points 154
- B.2 SDI2 Points 155
Related products and manuals for Washer dryers Bosch V20-UL
(2 pages)
Washer dryers Bosch WKD28320EU User Manual
(32 pages)
(32 pages)
Washer dryers Bosch WTG86400UC User Manual
(20 pages)
(20 pages)
© 2020, manymanuals.com. All rights reserved. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals