Bosch IDH182WC-102 Use and Care Manual download pdf (Page 12)

-12-

"#&#"!&"

This procedure shown in (Fig. 7) will enable

you to fasten ma terials together with your tool

without stripping, splitting or separating the

material.

First, clamp the pieces together and drill the

first hole 2/3 the diam eter of the screw. If the

material is soft, drill only 2/3 the proper

length. If it is hard, drill the entire length.

Second, unclamp the pieces and drill the

second hole the same diameter as the screw

shank in the first or top piece of wood.

Third, if flat head screw is used, countersink

the hole to make the screw flush with the

surface. Then, simply apply even pressure

when driving the screw. The screw shank

clearance hole in the first piece allows the

screw head to pull the pieces tightly together.

!$$#"#"

Variable speed control must be used with

caution for driving nuts and bolts with socket

set attach ments. The technique is to start

slowly, increasing speed as the nut or bolt runs

down. Set the nut or bolt snugly by slowing the

tool to a stop. If this procedure is not followed,

the tool will have a tendency to torque or twist

in your hands when the nut or bolt seats.

H Drill same

diameter as

screw shank.

H Countersink

same diameter

as screw head.

H Drill 2/3 diameter and

2/3 of screw length for

soft materials, full

length for hard

materials.

Screw

Apply a slight

even pressure

when driving

screws.

"#

&#"!&"

FIG. 7

".;?2,.

 $"! "!%

!#"";.?.7=2?.

6*27=.7*7,. 9.;/8;6.- +B >7*>=18;2C.-

9.;<877.5 6*B;.<>5= 27 62<95*,2708/

27=.;7*5 @2;.<*7- ,86987.7=< @12,1

,8>5- ,*><. <.;28>< 1*C*;- We recom -

mend that all tool service be performed by a

Bosch Factory Service Center or Authorized

Bosch Service Station. SERVICE MEN:

Disconnect tool and/or charger from power

source before servicing.

##!"

.*5.;=/8;+*==.;B9*,4<=1*=*;.7.*;270

=1.2; .7- 8/ 52/. If you notice decreased

tool performance or significantly shorter

running time between charges then it is time

to replace the battery pack. Failure to do so

can cause the tool to operate improperly or

damage the charger.

#$!#

Your Bosch tool has been properly lubricated

and is ready for use.

#!

The motor in your tool has been engineered

for many hours of dependable service. To

maintain peak efficiency of the motor, we

recommend it be examined every six months.

Only a genuine Bosch replacement motor

specially designed for your tool should be

used.

5.*7270

#8*?82-*,,2-.7=<*5@*B<

-2<,877.,= =1. =885 *7-8;

,1*;0.; /;86=1.98@.;<>995B +./8;.

,5.*7270 The tool may be cleaned most

effectively with com pressed dry air. 5@*B<

@.*; <*/.=B 08005.< @1.7 ,5.*7270 =885<

@2=1,869;.<<.-*2;

Ventilation openings and switch levers must

be kept clean and free of foreign matter. Do

not attempt to clean by inserting pointed

objects through opening.

.;=*27,5.*7270 *0.7=<

*7- <85?.7=< -*6*0.

95*<=2, 9*;=< Some of these are: gasoline,

car bon tetrachloride, chlorinated cleaning

solvents, ammonia and household detergents

that contain ammonia.

*27=.7*7,.

WARNING

CAUTION

BM 2610033029 10-13_BM 2610033029 09-13.qxp 10/1/13 11:49 AM Page 12

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 39 40

Comments to this Manuals

No comments

Bosch IDH182WC-102 Use and Care Manual Page 12

Comments to this Manuals

Related products and manuals for Cordless combi drills Bosch IDH182WC-102