Bosch GBH 36 VF-LI Specifications download pdf (Page 17)

English | 17

Bosch Power Tools 1 609 92A 04C | (14.12.12)

applications, with different accessories or poorly maintained,

the vibration emission may differ. This may significantly in-

crease the exposure level over the total working period.

An estimation of the level of exposure to vibration should also

take into account the times when the tool is switched off or

when it is running but not actually doing the job. This may signif-

icantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and the

accessories, keep hands warm, organise work patterns.

Assembly

Battery Charging

 Use only the battery chargers listed on the accessories

page. Only these battery chargers are matched to the lith-

ium ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The Lithium-Ion battery can be charged at any time without

reducing its service life. Interrupting the charging procedure

does not damage the battery.

The Lithium-Ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

Removing the battery

The battery 17 is equipped with two locking levels that should

prevent the battery from falling out when pushing the battery

unlocking button 12 unintentionally. As long as the battery is

inserted in the power tool, it is held in position by means of a

spring.

To remove the battery 17:

– Push the battery against the base of the power tool (1.) and

at the same time press the battery unlocking button 12 (2.).

– Pull the battery out of the power tool until a red stripe be-

comes visible (3.).

– Press the battery unlocking button 12 again and pull out

the battery completely.

Battery Charge-control Indication

The three green LEDs of the battery charge-control indicator

15 indicate the charge condition of the battery 17. For safety

reasons, it is only possible to check the status of the charge

condition when the machine is at a standstill.

–Push button 16 to indicate the charge condition (also pos-

sible when the battery is removed). The battery charge-

control indicator automatically goes out after approx.

5seconds.

When no LED lights up after pushing button 16, then the bat-

tery is defective and must be replaced.

During the charging procedure, the three green LEDs light up

one after the other and briefly go out. The battery is fully

charged when the three green LEDs light up continuously. The

three LEDs go out again approx. 5 minutes after the battery

has been fully charged.

The battery is equipped with a NTC temperature control

which allows charging only within a temperature range of be-

tween 0 °C and 45 °C. A long battery service life is achieved

in this manner.

Auxiliary Handle

 Operate your machine only with the auxiliary handle 19.

Changing the position of the auxiliary handle

(see figure A)

The auxiliary handle 19 can be set to any position for a secure

and low-fatigue working posture.

– Turn the bottom part of the auxiliary handle 19 in counter-

clockwise direction and swivel the auxiliary handle 19 to

the desired position. Then retighten the bottom part of the

auxiliary handle 19 by turning in clockwise direction.

Pay attention that the clamping band of the auxiliary handle is

positioned in the groove on the housing as intended for.

Adjusting the Drilling Depth (see figure B)

The required drilling depth X can be set with the depth stop 18.

– Press the button for the depth stop adjustment 13 and in-

sert the depth stop into the auxiliary handle 19.

The knurled surface of the depth stop 18 must face down-

ward.

– Insert the SDS-plus drilling tool to the stop into the SDS-

plus tool holder 3. Otherwise, the movability of the SDS-

plus drilling tool can lead to incorrect adjustment of the

drilling depth.

– Pull out the depth stop until the distance between the tip of

the drill bit and the tip of the depth stop correspond with

the desired drilling depth X.

Selecting Drill Chucks and Tools

For hammer drilling and chiselling, SDS-plus tools are re-

quired that are inserted in the SDS-plus drill chuck.

For drilling without impact in wood, metal, ceramic and plas-

tic as well as for screwdriving, tools without SDS-plus are

LED Capacity

Continuous lighting 3 x green ≥ 2/3

Continuous lighting 2 x green ≥ 1/3

Continuous lighting 1 x green <1/3

Flashing light 1 x green Reserve

OBJ_BUCH-283-006.book Page 17 Friday, December 14, 2012 1:10 PM

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 237 238

Comments to this Manuals

No comments

Bosch GBH 36 VF-LI Specifications Page 17

Comments to this Manuals

Related products and manuals for Cordless rotary hammers Bosch GBH 36 VF-LI