Bosch D9210C User Manual download pdf (Page 5)

GV4 Series Control Panel | Release Notes

5 Bosch Security Systems, Inc. | 11/11 | F01U261045-01

SDI2 Open Wire Detection

 The GV4 Ser

ies control panels support the

SDI2 bus to detect open communication

wires (SDI2 A+, SDI2 B-). This system fault is

annunciated on the keypads and optionally

reported to the central station.

2.1.6 B208 Octo-input Module

 The D9

412GV4 supports up to 24 Octo-input

modules. The D7412GV4 supports up to 7

Octo-input modules. The D7212GV4 supports

up to 3 Octo-input modules. Each Octo-input

module supports up to 8 configurable points.

2.1.7 B308 Octo-output Module

 The D9

412GV4 supports up to 12 Octo-output

modules. The D7412GV4 supports up to 6

Octo-output modules. The D7212GV4

supports up to 2 Octo-output modules. Each

Octo-output module supports up to 8

configurable relays.

2.1.8 B520 Auxiliary Power Supply Module

 All Gv4 Ser

ies control panels support up to 8

auxiliary 12V power supply modules.

 Each Auxiliary Power Supply module monitors

AC, up to 2 batteries, over current status and

tamper status. When detected, these

conditions are annunciated at the keypads,

reported to the central station, and viewable

in the RPS diagnostic screen.

2.1.9 B420 Network Interface Module

 The GV4 Ser

ies control panels support up to

two B420 modules on the SDI2 bus.

The communication modules on the SDI2

bus must be B420’s. The communication

modules on the SDI bus can be either

DX4020 or B420 modules. When the B420 is

installed on the SDI bus, it emulates the

DX4020 and is restricted to the functionality

of the DX4020.

 Configuration data such as the moduleís host

name, the DNS server address and encryption

keys can be configured in the GV4 control

panel using RPS or keypad programming. The

control panel configures the B420 network

interface modules automatically.

 By default, the control panel retrieves

configuration information in a newly installed

B420 network interface module. When

changes are made in the control panel, they

will be downloaded into the module.

 With DHCP enabled and a B420 network

interface module installed, the control panel

can automatically establish its IP address,

network gateway for internet or intranet

access if available.

If DHCP is disabled, the IP address, subnet

mask, and default gateway must be

configured manually.

 With a gateway defined, the control panel can

route network communication for central

station events and RPS network sessions

through the internet or a corporate intranet. If

DHCP is enabled, then the gateway will be

automatically assigned if available.

 With a DNS (Domain Name Server) address

configured and a B420 installed, the control

panel can dynamically find the IP addresses

of central station receivers and the PC

running RPS. If DHCP is enabled, then the

DNS address will be automatically obtained.

2.1.10 B820 Inovonics Interface Module

 The GV4 Ser

ies control panel supports one

B820 Inovonics Interface Module.

 RF devices such as wireless points, smoke

detectors, wireless RF repeaters, and keyfobs

can be added to the system through RPS or

keypad enrollment menus.

 Wireless keyfobs allow a user to arm or

disarm all authorized areas from anywhere in

the facility.

 The keyfob arm command can force arm the

system if the user's authority level allows

both keyfob arming and force arming.

 An RF Diagnostics menu is provided to

dynamically report the signal strength of

wireless points and wireless RF repeaters so

that they can be installed in an optimal

position.

 All points available in the GV4 Series control

panel can be configured to have a specified

source so multiple bus technologies can be

used simultaneously. Point sources include

ZONEX, Wireless, On-Board, and Access.

 A function of the GV4 Series control panel

allows the support of the Inovonics

EchoStream EN1224 Four-button Multi-

condition Belt Clip Pendant, and the EN1224-

ON Four-button Multi-condition Belt Clip

Pendant with On/Off capabilities.

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

Bosch D9210C User Manual Page 5

Comments to this Manuals

Related products and manuals for Networking Bosch D9210C