Bosch FNH180KL-16 Use and Care Manual download pdf (Page 12)

!(%#!"#%!

When using the tool in cold conditions the tool

will cycle slower than usual while driving the

f

irst nails. The cycle rate will increase as the

tool warms up. Keep tool warm to avoid

reduced cycle rate.

:9:? @>0 , 1=:E09?::7

Allow tool to thaw before

using. Moisture frozen in the tool may impede

internal components resulting in the risk of

injury and/or tool damage.

& ! 

7B,D> /4>.:990.?-,??0=D

;,.6 1=:8 ?::7 -01:=0

=08:A4929,47>1=:88,2,E490 This avoids

the risk of unintentional operation.

: 9:? /4>.:990.?-,??0=D

;,.6 1=:8 ?30 ?::7 B4?3

14920=:9?=4220= := B:=6.:9?,.?070809?

/0;=0>>0/ The tool can fire when

reconnected to battery pack.

1. Disconnect battery pack.

2. Pull back follower, pressing bypass lever of

the follower to allow follower to bypass nails

and slowly allow follower to return to nose of

the tool, see figure 8.

3. Tilt the tool with the magazine vertical and

the nose facing up, this will allow the nails to

slide to the back of the magazine.

4. Once the nails have slid back to the hold

back spring, press the tab on the hold back

spring to push the spring back and allow the

nails to come out of the magazine, see

figure 9.

: 9:? ,77:B ?30 9,47

1:77:B0= ?: 1=007D=0.:47

@4/0?301:77:B0=-D3,9/@9?474?=0,.30>

4?> 1@77 1:=B,=/ ;:>4?4:9 Free recoil of the

follower could result in damage to the follower

and/or magazine or your fingers could become

pinched.

"%!#'&$% %

The depth with which nails are driven into the

work piece can be adjusted using the depth

adjustment on the housing.

4>.:990.??30-,??0=D;,.6

1=:8 ?::7 -01:=08,6492

,/5@>?809?> Such precautionary safety

measures reduce the risk or unintentional tool

operation.

1. Disconnect tool from battery pack.

2. Remove nails from tool as described in the

“Nail Unloading” section of this manual.

3. Adjust tool driving depth:

•

To reduce the nail depth, turn the

adjustment knob towards the F17@>3G

icon, see figure 10.

!

WARNING

!

WARNING

!

WARNING

!

WARNING

!

WARNING

S

LID

E

FO

R

W

A

R

D

PRESS

Bypass Lever

PRESS

R

ELEA

S

E

N

A

ILS

FIG. 9

FIG. 8

TOO DEEP

%

@

=

9



?3

0



,

/

5

@

>

?80

9

?

6

9

:

-



.

:

@

9

?0

=

.

7

:

.

6

B4

>

0



TOO SHALLOW

FIG. 10

FIG. 11

%@=9?30,/5@>?809?

69:-.7:.6B4>0

-12-

BM 2610011761 10-10:BM 2610011761 07-10.qxp 10/5/10 9:24 AM Page 12

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 83 84

Comments to this Manuals

No comments