Bosch AMAX panel 2000 ICP-AMAX-P Installation Manual Page 25
- Page / 92
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
AMAX panel 2000 / AMAX panel 2000 EN User Guide | en 25
Bosch Sicherheitssysteme GmbH Installation Manual F.01U.241.127 | V4 | 2011.12
4.4 Walk test mode
This function allows code holders to test detection devices to ensure they are functioning
correctly. Before activating Walk test Mode, bypass any zones that are not required for
testing.
During the walk test, no walk test report is sent out to the control panel system.
To enter into Walk test Mode:
1. Enter your Code + [4] and press [#].
Two beeps sound and the STAY and AWAY indicators flash. The keypad beeps once per
second when walk test mode is active.
2. Unseal and seal the zones to be tested.
The keypad sounds one second beep and the siren sounds one beep each time when a
Zone status is changed.
4.5 Event Memory Recall mode
This function allows you to playback the last 254 system events that occurred.
Event Memory recall mode reports all alarms and each arming or disarming of the system and
helps in troubleshooting system faults.
The events are shown using the keypad indicators. Defined events are shown using keypad
indicators.
To enter Event memory Recall mode:
Enter your code + [5] and press #. Two beeps sound. The events are played back by the
keypad indicators in reverse chronological orer.
5 RF Power Fault
3 Warning Device Failure List
1 Warning Device 1 Disconnected
2 Warning Device 1 Short
3 Warning Device 2 Disconnected
4 Warning Device 2 Short
4 Telephone Line Fail
5 Date and Time Fail
6 Communications failure
1 Communication Failure 1
2 Communication Failure 2
3 Communication Failure 3
4 Communication Failure 4
7Tamper
1 On board Tamper
2Keypad 1 Tamper
3Keypad 2 Tamper
4 Keypad Lock out
5 Sensor Tamper (Zone 1-8)
6 Tamper Zone (Zone 1-8)
8 External Fault
- ICP-AMAX-P / ICP-AMAX-P-EN 1
- 1 Graphics 3
- 4 ICP-AMAX-P / ICP-AMAX-P-EN 4
- Table of Contents 5
- 1 Short Information 10
- 2 System Overview 11
- 3 Installation 12
- ICP-AMAX-P 13
- ICP-AMAX-P-EN 13
- 3.3 Programming 14
- Table 3.2 Keypad Indicators 15
- Figure 3.3 17
- Figure 3.2 17
- Figure 3.4 18
- 4User Guide 19
- 1 2 3 … 20
- Table 4.3 Keypad sounds 21
- 4.1 Arming the System 22
- 4.1.2 Arming in STAY mode 23
- 4.2 Disarming the System 24
- 4.4 Walk test mode 25
- 4.5 Event Memory Recall mode 25
- 4.6 Reset the Control Panel 26
- 4.7 Bypassing 26
- 4.9 Change individual code 27
- 4.11 Domestic Dialing 28
- 5.1 Accessory Modules Fail 30
- 5.1.2 Keypad 2 fail 31
- 5.1.3 DX3010 Fail 31
- 5.2 Power Faults 32
- 5.3 Warning Device Failure 33
- 5.4 Telephone Line Fault 34
- 5.5 Date and Time Fail 35
- 5.6 Communication Failure 35
- 5.7 Tamper Condition 36
- 5.7.4 Keypad lock out 37
- 5.7.5 Sensor Tamper 37
- 5.7.6 Zone Tamper 37
- 5.8 External Fault 38
- 6 System Functions 39
- 6.2 Siren Test 40
- 6.4 View date and time 40
- 6.5 Walk Test Mode 40
- 6.6 Event Memory Recall Mode 41
- 6.7 Reset panel/clear siren 41
- 6.8 Initiate a Modem Call 42
- 6.9 Send Test Report 42
- 6.10 Bypass Zones 42
- 6.11 Show Zone Type 42
- 6.14 Change individual code 43
- 6.15 Setting date and time 43
- 6.16 Add/delete User Codes 44
- 6.19 Enter Programming Mode 45
- 7 System Informations 1 48
- 7.4 Software 49
- 7.5 Domestic Dialing 50
- 7.6 Reporting Formats 50
- 7.7 Dialer Information 51
- Table 7.1 Dialing Digits 52
- 7.8 Access Codes 54
- 7.8.3 User Codes 55
- 8 System Informations 2 56
- BBBBB7DPSHU6ZLWFK 57
- BBBBB=RQH6ZLWFK 57
- 8.1.4 Zone Bypass 62
- 8.1.5 Forced Arming 62
- 8.1.6 Silent Alarm 62
- 8.1.7 Zone Lockout 62
- 8.1.8 Zone Tamper 63
- 8.1.9 Zone Fault 63
- 8.1.10 Zone Report 63
- 8.1.11 Zone Chime Mode 63
- 8.2.3 Auto Test Report 68
- 8.4 Output Process 69
- 8.5 System Event Time 72
- 8.6 Optional Equipment 73
- 9 Technical Data 75
- 9.2 Interface Description 77
- 10 Programming sheets 78
- 10.1.2 Domestic Programming 79
- 10.2.1 Report Options 79
- 10.4 Zone Programming 82
- 10.5 Output Programming 85
- 10.6.1 Installer code 87
- 10.6.2 User Codes 87
- 11 Troubleshooting 89
Related products and manuals for Security access control systems Bosch AMAX panel 2000 ICP-AMAX-P
(8 pages)© 2020, manymanuals.com. All rights reserved. | 0.732 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals