Bosch AMAX panel 2000 ICP-AMAX-P Installation Manual Page 42
- Page / 92
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
42 en | System Functions AMAX panel 2000 / AMAX panel 2000 EN
F.01U.241.127 | V4 | 2011.12 Installation Manual Bosch Sicherheitssysteme GmbH
6.8 Initiate a Modem Call
Enter your Code + [7] and press # two beeps sound and the control panel dials the callback
telephone number programmed in Location 154 – 169 in an attempt to connect to the
installer’s remote computer.
The remote computer must be running the remote programming software and must be set to
Waiting for an Incoming Call. If no callback telephone number is programmed, entering code
+[7] has no effect.
6.9 Send Test Report
This function allows code holder to send a test report to a Central Monitoring Station (CMS).
1. Enter your code + [8] and press #.
Two beeps sound and a test report is sent.
6.10 Bypass Zones
This function allows code holders to manually bypassone or more zones before arming the
system in AWAY Mode or STAY Mode. When a zone is bypassed, access is allowed into that
zone when the system is armed without activating an alarm.
The zone should be programmed as bypass zone enable. If the zone is not programmed as
bypass zone, then it cannot be bypassed manually as bypass zone.
For example, you might want to isolate a zone before arming the system because a zone
passive infrared (PIR) detector is activating false alarms or because you need to leave a pet
inside a particular zone while you are away.
Key-switch zone can’t be bypassed.
The non-used zone can’t be bypassed.
Alarm Zone bypass:
1. Zones that have been bypassed will report to CMS at once.
2. When the zone bypassed is restored, it will send the restore report to CMS immediately.
3. When the system is disarmed again after arming, the bypassed zones will be restored. It
will send the bypassed restore report to CMS.
Bypass Steps:
1. Enter your Code + [9] and press [#] . the AWAY and STAY indicators flash.
2. Enter the number of the zone to be bypassed and press [*]. Repeat Step 2 for each zone
you want to isolate.
3. To cancel any isolated zone, enter the number of isolated zone and press [*]. Repeat
Step 3 for each zone you have bypassed.
4. Press [#] to exit.
For example:
To manually bypass zones 1,3 and 4, press:
[Code][9][#][1][*][3][*][4] [*][#]
6.11 Show Zone Type
This function allows code holders to see the zone type
NOTICE!
You can only reset Alarms Faults or Tamper conditions, when the related contact or function is
idle.
- ICP-AMAX-P / ICP-AMAX-P-EN 1
- 1 Graphics 3
- 4 ICP-AMAX-P / ICP-AMAX-P-EN 4
- Table of Contents 5
- 1 Short Information 10
- 2 System Overview 11
- 3 Installation 12
- ICP-AMAX-P 13
- ICP-AMAX-P-EN 13
- 3.3 Programming 14
- Table 3.2 Keypad Indicators 15
- Figure 3.3 17
- Figure 3.2 17
- Figure 3.4 18
- 4User Guide 19
- 1 2 3 … 20
- Table 4.3 Keypad sounds 21
- 4.1 Arming the System 22
- 4.1.2 Arming in STAY mode 23
- 4.2 Disarming the System 24
- 4.4 Walk test mode 25
- 4.5 Event Memory Recall mode 25
- 4.6 Reset the Control Panel 26
- 4.7 Bypassing 26
- 4.9 Change individual code 27
- 4.11 Domestic Dialing 28
- 5.1 Accessory Modules Fail 30
- 5.1.2 Keypad 2 fail 31
- 5.1.3 DX3010 Fail 31
- 5.2 Power Faults 32
- 5.3 Warning Device Failure 33
- 5.4 Telephone Line Fault 34
- 5.5 Date and Time Fail 35
- 5.6 Communication Failure 35
- 5.7 Tamper Condition 36
- 5.7.4 Keypad lock out 37
- 5.7.5 Sensor Tamper 37
- 5.7.6 Zone Tamper 37
- 5.8 External Fault 38
- 6 System Functions 39
- 6.2 Siren Test 40
- 6.4 View date and time 40
- 6.5 Walk Test Mode 40
- 6.6 Event Memory Recall Mode 41
- 6.7 Reset panel/clear siren 41
- 6.8 Initiate a Modem Call 42
- 6.9 Send Test Report 42
- 6.10 Bypass Zones 42
- 6.11 Show Zone Type 42
- 6.14 Change individual code 43
- 6.15 Setting date and time 43
- 6.16 Add/delete User Codes 44
- 6.19 Enter Programming Mode 45
- 7 System Informations 1 48
- 7.4 Software 49
- 7.5 Domestic Dialing 50
- 7.6 Reporting Formats 50
- 7.7 Dialer Information 51
- Table 7.1 Dialing Digits 52
- 7.8 Access Codes 54
- 7.8.3 User Codes 55
- 8 System Informations 2 56
- BBBBB7DPSHU6ZLWFK 57
- BBBBB=RQH6ZLWFK 57
- 8.1.4 Zone Bypass 62
- 8.1.5 Forced Arming 62
- 8.1.6 Silent Alarm 62
- 8.1.7 Zone Lockout 62
- 8.1.8 Zone Tamper 63
- 8.1.9 Zone Fault 63
- 8.1.10 Zone Report 63
- 8.1.11 Zone Chime Mode 63
- 8.2.3 Auto Test Report 68
- 8.4 Output Process 69
- 8.5 System Event Time 72
- 8.6 Optional Equipment 73
- 9 Technical Data 75
- 9.2 Interface Description 77
- 10 Programming sheets 78
- 10.1.2 Domestic Programming 79
- 10.2.1 Report Options 79
- 10.4 Zone Programming 82
- 10.5 Output Programming 85
- 10.6.1 Installer code 87
- 10.6.2 User Codes 87
- 11 Troubleshooting 89
Related products and manuals for Security access control systems Bosch AMAX panel 2000 ICP-AMAX-P
(8 pages)© 2020, manymanuals.com. All rights reserved. | 2.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals