Bosch AMAX panel 2000 ICP-AMAX-P Installation Manual Page 32
- Page / 92
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
32 en | Fault and Tamper Description AMAX panel 2000 / AMAX panel 2000 EN
F.01U.241.127 | V4 | 2011.12 Installation Manual Bosch Sicherheitssysteme GmbH
Communication with DX4020/ITS-DX4020G is normal and fault is reset.
Supervise:
1. Report the DX4020/ITS-DX4020G fault to configured destination on location 140 when
the fault is detected.
2. Slow flash FAULT indicator (refer to the detailed description in chapter keypad
indicators)
3. When the fault is reset, send the restored report to the configured destinations. The
FAULT indicator is turned off when there is no other system fault.
5.2 Power Faults
The zone indicator 2 lights to indicate Power Faults. Enter [2] to step to Power Faults list for
more information.
5.2.1 AC Failure
Condition:
1. 18V AC supply deficiency to panel caused by tansformer .
2. 220V power supply fuse broken.
3. 220V power supply disconnected.
Restore:
AC MAINS supply is reconnected and fault is reset.
1. Monitor the voltage by MPU.
2. If the AC fault is not restored in 1 hour after the fault occured, report the fault to
configured destination on location 140.
3. Slow flash FAULT indicator (refer to the detailed description in chapter keypad
indicators)
4. As the AC supply is reconnected, the MAINS indicator is back to light (except in
Programming Mode or Code Functions Mode ).
5. When the fault is reset, send the restored report to the configured destinations.
5.2.2 Battery Failure
Condition:
1. Battery voltage is lower than 11.8V+-1%.
2. No battery connected.
Restore:
When Battery voltage rises to 12.5V+-1%, Dynamic Battery test is performed (time set in
Programming location 191) and fault is reset.
Supervise:
1. The system performs a Dynamic Battery Test every time (set in location 191) and every
time the system is armed or reset.
2. Report the low battery to the configured destination programmed on location 140.
3. Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators)
4. When the fault is reset, send the restored report to the configured destinations. The
FAULT indicator is turned off when there is no other system fault.
5.2.3 AUX Power Supply Fail
Condition:
Aux Power Supply Voltage is lower than 9V+-5%.
Restore:
Voltage is raised to 12.5V+-5% and fault is reset.
- ICP-AMAX-P / ICP-AMAX-P-EN 1
- 1 Graphics 3
- 4 ICP-AMAX-P / ICP-AMAX-P-EN 4
- Table of Contents 5
- 1 Short Information 10
- 2 System Overview 11
- 3 Installation 12
- ICP-AMAX-P 13
- ICP-AMAX-P-EN 13
- 3.3 Programming 14
- Table 3.2 Keypad Indicators 15
- Figure 3.3 17
- Figure 3.2 17
- Figure 3.4 18
- 4User Guide 19
- 1 2 3 … 20
- Table 4.3 Keypad sounds 21
- 4.1 Arming the System 22
- 4.1.2 Arming in STAY mode 23
- 4.2 Disarming the System 24
- 4.4 Walk test mode 25
- 4.5 Event Memory Recall mode 25
- 4.6 Reset the Control Panel 26
- 4.7 Bypassing 26
- 4.9 Change individual code 27
- 4.11 Domestic Dialing 28
- 5.1 Accessory Modules Fail 30
- 5.1.2 Keypad 2 fail 31
- 5.1.3 DX3010 Fail 31
- 5.2 Power Faults 32
- 5.3 Warning Device Failure 33
- 5.4 Telephone Line Fault 34
- 5.5 Date and Time Fail 35
- 5.6 Communication Failure 35
- 5.7 Tamper Condition 36
- 5.7.4 Keypad lock out 37
- 5.7.5 Sensor Tamper 37
- 5.7.6 Zone Tamper 37
- 5.8 External Fault 38
- 6 System Functions 39
- 6.2 Siren Test 40
- 6.4 View date and time 40
- 6.5 Walk Test Mode 40
- 6.6 Event Memory Recall Mode 41
- 6.7 Reset panel/clear siren 41
- 6.8 Initiate a Modem Call 42
- 6.9 Send Test Report 42
- 6.10 Bypass Zones 42
- 6.11 Show Zone Type 42
- 6.14 Change individual code 43
- 6.15 Setting date and time 43
- 6.16 Add/delete User Codes 44
- 6.19 Enter Programming Mode 45
- 7 System Informations 1 48
- 7.4 Software 49
- 7.5 Domestic Dialing 50
- 7.6 Reporting Formats 50
- 7.7 Dialer Information 51
- Table 7.1 Dialing Digits 52
- 7.8 Access Codes 54
- 7.8.3 User Codes 55
- 8 System Informations 2 56
- BBBBB7DPSHU6ZLWFK 57
- BBBBB=RQH6ZLWFK 57
- 8.1.4 Zone Bypass 62
- 8.1.5 Forced Arming 62
- 8.1.6 Silent Alarm 62
- 8.1.7 Zone Lockout 62
- 8.1.8 Zone Tamper 63
- 8.1.9 Zone Fault 63
- 8.1.10 Zone Report 63
- 8.1.11 Zone Chime Mode 63
- 8.2.3 Auto Test Report 68
- 8.4 Output Process 69
- 8.5 System Event Time 72
- 8.6 Optional Equipment 73
- 9 Technical Data 75
- 9.2 Interface Description 77
- 10 Programming sheets 78
- 10.1.2 Domestic Programming 79
- 10.2.1 Report Options 79
- 10.4 Zone Programming 82
- 10.5 Output Programming 85
- 10.6.1 Installer code 87
- 10.6.2 User Codes 87
- 11 Troubleshooting 89
Related products and manuals for Security access control systems Bosch AMAX panel 2000 ICP-AMAX-P
(8 pages)© 2020, manymanuals.com. All rights reserved. | 3.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals