Bosch DWK09G660 User Manual download pdf (Page 6)

In any case, consult your responsible Master Chimney Sweep.

He is able to assess the house's entire ventilation setup and will

suggest the suitable ventilation measures to you.

Unrestricted operation is possible if the vapour extractor hood is

operated exclusively in the circulating-air mode.

Danger of death!

Risk of poisoning from flue gases that are drawn back in. If

installing a ventilation system in a room with a heat-producing

appliance connected to a chimney/flue, the electricity supply to

the hood must be equipped with a suitable safety switch.

Risk of fire!

Grease deposits in the grease filter may catch fire. The specified

safety distances must be observed in order to prevent an

accumulation of heat. Observe the specifications for your

cooking appliance. If gas and electric hobs are operated

together, the largest specified distance applies.

Only one side of the appliance may be installed directly next to

a high-sided unit or a wall. The distance between the appliance

and wall or high-sided unit must be at least 50 mm.

Risk of injury!

■ Components inside the appliance may have sharp edges.

Wear protective gloves.

Risk of injury!

■ The appliance may fall down if it has not been properly

fastened in place. All fastening components must be fixed

firmly and securely.

Risk of injury!

■ The appliance is heavy. To move the appliance, 2 people are

required. Use only suitable tools and equipment.

Risk of electric shock!

Components inside the appliance may have sharp edges. These

may damage the connecting cable. Do not kink or pinch the

connecting cable during installation.

Danger of suffocation!

Packaging material is dangerous to children. Never allow

children to play with packaging material.

General information

Exhaust air mode

Note: The exhaust air must not be conveyed into a functioning

smoke or exhaust gas flue or into a shaft which is used to

ventilate installation rooms which contain heat-producing

appliances.

■ Before conveying the exhaust air into a non-functioning smoke

or exhaust gas flue, obtain the consent of the heating

engineer responsible.

■ If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Exhaust duct

Note: The appliance manufacturer does not assume any

warranty for complaints attributable to the pipe section.

■ The appliance achieves its optimum performance by means of

a short, straight exhaust air pipe and as large a pipe diameter

as possible.

■ Because of long rough exhaust air pipes, many of which are

pipe bends or have diameters smaller than 150 mm, the

optimum extraction performance is not achieved and fan

noise is increased.

■ The pipes or hoses for laying the exhaust duct must consist of

non-combustible material.

Round pipes

An inner diameter of 150 mm, but at least 120 mm, is

recommended.

Flat ducts

The inner cross-section must correspond to the diameter of the

round pipes.

Ø 150 mm approx. 177 cm

Ø 120 mm approx. 113 cm

■ Flat ducts should have no sharp deflections.

■ Use sealing strip for deviating pipe diameters.

Checking the wall

■ The wall must be level, vertical and adequately load-bearing.

■ The depth of the bore holes must be the same length as the

screws. The wall plugs must have a secure grip.

■ The enclosed screws and wall plugs are suitable for solid

brickwork. Suitable fasteners must be used for other

structures (e.g. plasterboard, porous concrete, poroton

bricks).

■ The max. weight of the extractor hood is 40 kg.

Electrical connection

: Risk of electric shock!

Components inside the appliance may have sharp edges. These

may damage the connecting cable. Do not kink or pinch the

connecting cable during installation.

The required connection data can be found on the rating plate

inside the appliance; to do this, remove the metal mesh grease

filter.

Length of the cable: approx. 1.30 m

This appliance complies with the EC interference suppression

regulations.

This appliance may be connected to a correctly installed

earthed socket only.

Attach the earthed socket preferably inside the flue duct.

■ The earthed socket should be connected via its own circuit.

■ If the earthed socket is no longer accessible following

installation of the appliance, a disconnecter must be fitted as

for a permanent connection.

If a permanent connection is required, the installation must

feature an all-pole disconnecter (circuit breakers, fuses and

contactors) with a min. 3 mm contact opening. The permanent

connection may be installed by an electrician only.

Appliance dimensions (Fig. A)

Safety clearances (Fig. B)

Preparing for installation

Caution!

Ensure that there are no electric wires, gas or water pipes in the

area where holes are to be made.

1. Mark a vertical centre line on the wall from the ceiling to the

lower edge of the extractor hood. (Fig. 1)

2. Mark holes for the flue's fixing brackets. The centre of the fixing

brackets is identified with a notch. Place the fixing brackets in

the centre of the centre line, align it horizontally and mark the

positions of the holes. The distance X between the two fixing

brackets corresponds to the length of the upper part of the flue.

(Fig. 1a)

3. Mark holes for the mounting brackets and for the means of

securing the appliance. (Fig. 1b)

4. Drill the holes.

5. Press in the wall plugs flush with the wall.

Fitting the appliance

Fitting the wall bracket

1. Screw on the fixing bracket for the flue duct. (Fig. 1a)

2. Screw on mounting brackets for the appliance. (Fig. 1b)

Attaching and aligning the appliance

: Risk of injury!

Components inside the appliance may have sharp edges. Wear

protective gloves.

1. Remove metal grease filter; see instructions for use.

2. Initially remove the protective foil from the back of the

appliance and, following installation, remove the foil

completely.

3. When attaching the appliance, ensure that it engages firmly

with the brackets. (Fig. 2)

4. Align the appliance horizontally by turning the screws on the

mounting brackets. The screws are accessible from the inside

of the appliance. If required, the appliance can be moved a

little to the right or to the left. (Fig. 2a)

Securing the appliance

1. Screw in the retaining screws on the inside of the appliance.

(Fig. 2b)

2. Fit metal grease filter; see instructions for use.

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Bosch DWK09G660 User Manual Page 6

Comments to this Manuals

Related products and manuals for Refrigerators Bosch DWK09G660