Bosch D7412G User Manual Page 20
- Page / 142
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412G/D7412G | Program Entry Guide | 2.0 9000MAIN EN | 20
Bosch Security Systems | 1/04 | 47775E
Test Reports
0101
0101
0101
To send a single Test Report (R# Test
Report), enable Sked Function Code #9
(Test Report) in the Skeds section of the
program.
To expand this Test Report to include any
off-normal point condition or other off-
normal conditions of events listed in Diag
Reports as a Non-status Event following a
Test Report, Expand Test Rpt in Section
2.2 Phone Parameters must be
programmed Yes.
Events R# Log Threshold, R# Log
Overflow, and R# RAM Fail are added to
the reports sent with Expanded Test
Reports if they are enabled in RAM Reports
and Expand Test Rpt is also enabled.
To initiate a Status Report, which includes
all R# S: ____ Events as a Status Event (as
opposed to a Non-status Event), Sked
Function Code #10 must be enabled in the
Skeds section of the program.
Reporting off-normal conditions as a Status
Report following a Test Report is required
by some automation systems. Reporting off-
normal conditions as a Non-status Report,
which follows a Test Report, is required for
other automation systems.
An off-normal condition is any point which is
missing, trouble, supervisory, or in alarm (as
opposed to normal). Also, points not
cleared at the command center report as
off-normal.
Control Panels with Firmware version 6.30
or higher can generate an Expanded Off-
Normal Test Report by using Sked Function
Code 28 or a Non-Expanded Off-Normal
Test Report using Sked Function Code 29.
To generate this event, one or more points
must be in an off-normal state at the time
the Sked executes. Expanded Off-Normal
Test Reports include the Off Normal Test
Report Event as well as events for any
points that are in an off-normal state at the
time the report is generated. Non-Expanded
Off-Normal Test Report Events are only
sent when a point is in the off-normal state
but only sends the Off Normal Test Report
Event.
Table 12: Test Reports
Report Selections Description
R# S: Alarm
Yes, No
Status Alarm Report
R# S: Trouble
Yes, No
Status Trouble
Report
R# S:
Supervised
Yes, No
Status Supervised
Report
R# Status
Report
Yes, No
Status Report
R# S: Open
Yes, No
Status Open Report
R# S: Close
Yes, No
Status Close Report
R# Test Report
Yes, No
Test Report
R# S: Perim
Inst
Yes, No
Status Perimeter
Instant Arm Report
R# S: Perim
Delay
Yes, No
Status Perimeter
Delay Arm Report
R# S: Fire Supv
Yes, No
Status Fire
Supervision Report
R# S: Fire
Alarm
Yes, No
Status Fire Alarm
Report
R# S: Fire Trbl
Yes, No
Status Fire Trouble
Report
R# S: Msng
Fire
Yes, No
Status Fire Missing
Report
R# S:
MsngBurgTr
Yes, No
Status Burg Missing
Trouble Report
R# S:
MsngBurgAl
Yes, No
Status Burg Missing
Alarm Report
R# S:
FireSpMsng
Yes, No
Status Fire
Supervision Missing
Report
R# S:
SuperMsng
Yes, No
Status Non-fire
Supervision Missing
Report
R# S:
DrLeftOpen
Yes, No
Status Door Left
Open Report
Diag Reports
Selecting Yes enables sending a report when the
event occurs. If the off-normal state of the following
events (indicated with an *) still exist, they report
when a Test Report (see the
Test Reports
sub-
prompt in Section 2.3.8 Dialing Attempts) is initiated
and Expanded Test Rpt is programmed Yes.
- D9412G/D7412G 1
- Trademarks 2
- Documentation Conventions 2
- Table of Contents 3
- 1.0 Introduction 5
- 1.4 New Features 6
- Table 3: continued 7
- 1.5 Product Handlers 8
- 1.6 Programming Options 8
- FILENAME 9
- NEWRECORD 9
- 2.0 9000MAIN 11
- 2.2 Phone Parameters 12
- DTMF Dialing 13
- Phone Supv Time 14
- Alarm On Fail 14
- Buzz on Fail 14
- Two Phone Lines 14
- 2.3 Routing 15
- R# Primary Device 17
- R# Backup Device 17
- View Events? 17
- Fire Reports 18
- Burglar Reports 18
- User Reports 19
- Test Reports 20
- Diag Reports 20
- Relay Reports 21
- AutoFunc Reports 21
- RAM Reports 22
- Point Reports 22
- 2.4 Enhanced Routing 23
- RG# Primary SDI 24
- RG# Backup SDI 24
- RG# Primary Pager 25
- 2.5 Power Supervision 27
- AC Fail/Res Rpt 28
- AC Tag Along 28
- 2.6 Printer Parameters 29
- 2.7 RAM Parameters 31
- RAM Passcode 32
- Log % Full 32
- RAM Call Back 32
- RAM Line Monitor 32
- Answer Armed 33
- Answer Disarmed 33
- 2.8 Miscellaneous 34
- 2.9 Area Parameters 34
- A# Acct Number 35
- A# FA Bypass Max 36
- A# Delay Res 36
- A# Exit Tone 36
- A# Exit Dly Time 36
- A# Auto Watch 37
- A# Verify Time 37
- A# Duress Enable 38
- A# Area Type 39
- D## CC# Scope 40
- A# Fire Pat 41
- A# Burg Time 41
- A# Burg Pat 41
- A# Single Ring 41
- A# Fire Time 41
- A# Bell Test 42
- A# Acct O/C 43
- A# Area O/C 44
- A# Disable O/C in Window 44
- A# Auto Close 44
- A# Fail to Open 44
- A# Fail to Close 45
- A# Restrictd O/C 45
- 2.10 Command Center 46
- CC# Supervised 47
- CC# Area Assign 47
- CC# Scope 47
- CC# A1[through A8] in Scope 48
- CC# Entr Key Rly 48
- CC# Entr Cycl Dr 48
- CC# Assign Door 49
- CC# Trouble Tone 49
- CC# Entry Tone 49
- CC# Exit Tone 49
- Program Record Sheet 50
- Area # Acct Is On 51
- Custom Function 51
- CF### Text 51
- CF### Key Strokes 52
- 2.11 User Interface 53
- P## Type 1 55
- Expand Test Rpt 55
- L## Access Level 56
- L## Disarm Level 56
- P## Bypassable 57
- P## FA Retrnable 57
- Bypass Returnable 57
- P## Resettable 57
- P## Type 58
- S## Time 58
- Authority Level 59
- L## Disarm 59
- L## Master Arm Delay 59
- .L## Mstr Arm Inst 59
- L## Fire Test 61
- L## Send Report 61
- L## Door Control 61
- L## Cycle Door 61
- L## Unlock Door 62
- L## Secure Door 62
- L## Access Ctl Lvl 62
- L## Passcode Disarm 66
- L## Security Level 66
- 2.12 Function List 67
- 2.13 Relay Parameters 67
- A# Alarm Bell 68
- A# Fire Bell 69
- A# Reset Sensors 69
- A# Force Armed 69
- A# Watch Mode 69
- A# Area Armed 70
- A# Area Fault 70
- A# Duress Relay 70
- A# Perim Fault 70
- A# Silent Alarm 70
- AC Failure 71
- Battery Trouble 71
- Phone Fail 71
- P## Type 0 72
- P## Fire 72
- 3.0 RADXUSR1/RADXUSR2 73
- User ### 74
- U### Passcode 74
- U### User Group 75
- U### Name 75
- U### Mstr Site 75
- U### Mstr C/D 76
- U### SU1 through SU3 Site 76
- U### SU1 through SU3 C/D 76
- 4.0 RADXPNTS 77
- P## Ent Tone Off 78
- P## Entry Delay 78
- Point Response 80
- Local Armed 80
- Local Disarmed 80
- P## Pt Response 82
- P## Silent Bell 83
- P## Ring Til Rst 83
- P## Audible After 2 Failures 84
- P## Invisible Pt 84
- P## Buzz On Fault 85
- P## Watch Point 85
- P## RlyResp Type 86
- P## Disp as Dvc 86
- P## Local While Disarmed 86
- P## Local While Armed 86
- P## Disable Rst 87
- P## BP Retrnable 87
- P## Swinger Byps 88
- P## Defer BP Report 89
- P## Cross Point 89
- P## Fire Point 90
- 4.2 Point Assignments 91
- P### Point Index 92
- P### Area Assign 92
- P### Debounce 92
- P### BFSK/Relay 93
- P### Point Text 93
- 4.3 COMMAND 7 and COMMAND 9 94
- 5.0 RADXSKED 95
- Early Begin 96
- W# Open Window Stop 97
- W# Close Early Begin 98
- W# Close Window Start 99
- W# Close Window Stop 99
- Xept Holiday 100
- W# Xept Holiday 100
- User Windows # 102
- UW# User Group 102
- 5.2 Skeds 104
- S## Function Code 105
- S## Area # 106
- Relay Number 106
- Cmd Center 108
- Custom Func 108
- 5.3 Holiday Indexes 113
- Holiday Index 1 114
- 6.0 RADXAUX1 115
- 6.4 SDI RAM Parameters 116
- Enable SDI RAM 117
- RAM IP Address 1 118
- RAM IP Address 2 118
- RAM IP Address 3 118
- RAM IP Address 4 118
- 6.5 Enhanced Communications 122
- Path # IP Add1 123
- Path # IP Add2 123
- Path # IP Add3 123
- Path # IP Add4 123
- 6.6 SDI RAM/Enhanced 125
- Communications Configuration 125
- Parity/Stop 126
- RTS Control 126
- DTR Control 126
- 9133 Supervision 126
- Base Port Number 126
- 6.7 Miscellaneous 127
- 6.8 Cross Point Parameters 128
- Cross Point Time 129
- 7.0 RADXAXS 131
- D# Interlock Point 132
- D# Auto Door? 132
- D# Fire Unlock? 132
- D# Disarm on Open? 132
- 7.2 Strike Profile 133
- 7.3 Event Profile 134
- D# Access Granted? 135
- D# No Entry? 135
- D# Enter Request? 135
- Programming Prompts 136
- Directory 136
- © 2003 Bosch Security Systems 142
Related products and manuals for Fire protection Bosch D7412G
Fire protection Bosch D9124 User Manual
(4 pages)
(4 pages)
Fire protection Bosch D9112 User Manual
(87 pages)
(87 pages)
Fire protection Bosch DS9400 User Manual
(8 pages)
(8 pages)
Fire protection Bosch FPD-7024 User Manual
(122 pages)
(122 pages)
Fire protection Bosch D7024 User Manual
(22 pages)
(22 pages)
Fire protection Bosch D9412GV2 User Manual
(74 pages)
(74 pages)
Fire protection Bosch D296/D297 User Manual
(12 pages)
(12 pages)
Fire protection Bosch D1257 Specifications
(16 pages)
(16 pages)
Fire protection Bosch D1256 User's Guide
(28 pages)
(28 pages)
Fire protection Bosch D1256 Specifications
(16 pages)
(16 pages)
Fire protection Bosch D1257 Installation Guide
(154 pages)
(154 pages)
© 2020, manymanuals.com. All rights reserved. | 3.878 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals