Bosch VG5-825-ETEV Specifications download pdf (Page 85)

FLIR

26-3

Limitations

Known Issues

Model Known Camera Limitations

1 F-Series

D-Series

PT-Series

Due to a necessity of FLIR camera video hardware re-start, it may

take about 48 seconds for the video stream to come back after any

stream property changes.

2 F-Series

D-Series

PT-Series

Camera may take more than 5s to respond to a CGI command, this

may cause NVR to timeout. This is camera performance issue.

3 F-Series

D-Series

PT-Series

User can only view camera’s video standard format setting (NTSC

or PAL) on NVR. We do not recommend the Video Standard be

changed from the default. This is due to the requiring FLIR camera

hardware change. The effect of changing the Video Standard are:

Incorrect Image Resolution and FPS will be displayed on Camera

WebGUI, NVR and victor Client.

4 F-Series

D-Series

PT-Series

NVR requires a response from cameras within 5 seconds. As a

result, changing resolution on the NVR may result an error

message. If the change is made again on the NVR it will work. The

error message is not always received.

5 F-Series

D-Series

PT-Series

MJPEG Live video Pixilated is caused by a low Q set by default on

the camera (Q=25). Once this value is set to 75 the Pixilation

disappears. The problem only arises with MJPEG.

6 F-Series

D-Series

PT-Series

After changing video channel resolution, frame rate and/or video

codec type on a stream, video stream will become unavailable for

about 45 seconds. This is because changing video channel

configuration parameters (Bitrate, Frame rate, Resolution and

Video Codec Type) requires reset of camera’s video hardware.

7 F-Series

D-Series

PT-Series

User is able to add camera to NVR using wrong password from

password group. This is because FLIR camera doesn’t require

authentication.

8 F-Series

D-Series

PT-Series

Video freeze may occur when changing heat distributions or many

moving objects are detected by camera. Wireshark traces shown

that the camera under test stops transmitting UDP/RTP packets for

a short period of time.

9 D-Series

PT-Series

Camera zoom in and zoom out only work on NVR. Camera zoom in

and zoom out do not work on Victor Client. This is because Victor

Client uses “Continuous Zoom” method to implement zoom in and

zoom out and FLIR cameras have no CGI support for continuous

zoom.

10 D-Series

PT-Series

Preset cannot be used to set Zoom In and Zoom Out.

PTScanListPointCurrentValuesSet is used to save a preset

position. This CGI does not save the zoom setting into the preset

position.

11 D-Series

PT-Series

F-Series

The video source format of FLIR cameras is pre-configured at the

factory. Switching the video source format through FLIR web or

Nexus interface will not take effect until the required FLIR camera

hardware components are installed. Customers must contact FLIR

to obtain the required hardware components and follow their

installation procedure.

Model Known Issues

F-Series Due to VE-API limitation, ZOOM only camera will not be supported as PTZ camera.

Therefore, ZOOM feature of F-Series will not be supported.

F-Series

D-Series

PT-Series

Communication channel between NVR client and camera server through port 8080

becomes unavailable occasionally. If HTTP connections through port 8080 cannot be

established, FLIR camera sever will not be able to respond to CGI commands sent by

NVR client. When this happens, user must try to re-establish the HTTP connection

through port 8080. Table 1 lists steps for trouble shooting HTTP connection between

NVR client and FLIR camera server (Nexus Server).

1 2 ... 80 81 82 83 84 85 86 87 88 89 90 ... 107 108

Comments to this Manuals

No comments

Bosch VG5-825-ETEV Specifications Page 85

Comments to this Manuals

Related products and manuals for Security cameras Bosch VG5-825-ETEV