Bosch EHP 6-11 LW Installation Guide Page 20
- Page / 80
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
20
FOR THE USER
All menus relating to temperature sensors
All the menus associated with the heat pump temperature sensors are shown
below. Note that you cannot make any settings in these menus, only read the
current values. Some menus are standard for all models of Ecolane SE while
others are only available in combination with different accessories.
The sensors give an alarm if the temperature is outside of the permitted
range/values.
Note
All sensors are not included as
standard on the heat pump, some are
available as accessories for different
application areas. See more informa-
tion under respective menus.
The menu shows the temperature in the heating system’s return, i.e. the water from the
radiators back to the heat pump accord. to clockeating mode. The temperature varies with
the outdoor temperature.
The menu shows the outdoor temperature. Some deviation compared to the true tempera-
ture may occur due to thermal radiation from the house to the installed outdoor sensor.
The menu shows the set and present temperature in the lower section of the outer
container in the hot water heater. The temperature is approximately 5ºC lower than the
temperature of the hot water inside the inner container.
The menu only applies together with a fl ow sensor. If an extra curve with mixing valve
is used, for example, for a fl oor heating system, you can see the temperature on the fl ow
water in the circuit. The temperature varies with the outdoor temperature.
The menu only applies together with a room sensor. The menu shows the set point value
and present temperature in the room where the sensor is fi tted.
The menu shows the compressor’s working temperature. The temperature varies
between 70ºC and 125ºC during operations.
The menu shows the temperature of the radiator water as it leaves the heat pump. It
varies depending on the outdoor temperature and whether the heat pump is accord. to
clockot water production mode.
The menu shows the temperature of the water that is led into the heat pump. It varies
depending on the outdoor temperature and whether the heat pump is accord. to clockot
water production mode. The heat pump stops at 57ºC for reasons of safety.
The menu shows the temperature of the heat transfer fl uid that is led into the heat pump
from the bore hole or the ground. It can vary between -5ºC to +15ºC during a season.
The menu shows the temperature of the heat transfer fl uid that is led out of the heat
pump to the bore hole or the ground. Normally, during operations, it is 1.5 - 5.0 degrees
lower than the heat transfer fl uid that is led into the heat pump.
Basic functions - Customer level 1
Temperature readings
Return radiator GT1
Off 41.3
O
now 40.3
O
Return
Temperature readings
Out GT2
14,0°
Return
Temperature readings
Hot water GT3
Set 51.0°
now 50.0°
Return
Temperature readings
Shunt, fl ow GT4
Set 40.3°
now 43.0°
Return
Temperature readings
Room GT5
Set 20.0°
now 19.5°
Return
Temperature readings
Compressor GT6
90,0°
Return
Temperature readings
Heat tr fl uid out GT8
45,0°
Return
Temperature readings
Heat tr fl uid in GT9
40,3°
Return
Temperature readings
Ht trfl d(coll)inGT10
0,0°
Return
Temperature readings
Httrfl d(coll)outGT11
-4,0°
Return
- Heat Pump Compress 3000 1
- Bosch, 2009-11-30 2
- Article number: 6 720 642 634 2
- Version 2009/11 2
- Table of Contents 3
- For the user 5
- Heat pump 7
- Control unit 10
- FOR THE USER 11
- Control with outdoor sensor 11
- Control panel 12
- Menu dial 13
- How to use the control panel 13
- ( Customer level 1) 13
- Set the heating 15
- Change the curve slope 16
- ne-tuned in a 17
- (Customer level 2) 21
- Temperature settings 22
- Fine-tune the mixing valve 23
- Timer control 24
- Hot water settings 24
- Set the time and date 26
- Alarms given by the heat pump 27
- Maintenance 28
- Protective anode 29
- Particle fi lter 29
- What to do if a fault occurs 30
- All alarms 31
- Motor cut-out HTF pump (MB2) 32
- Low pressure switch (LP) 33
- High pressure switch (HP) 34
- Electric cassette (EK) 34
- Power failure (3-phase) 35
- 3-phase incorrect (3-phase) 35
- Sensor fault 37
- Anode error 38
- For the Installer 39
- Checklist 40
- What the shipment includes 41
- FOR THE INSTALLER 42
- LWM model 42
- LW model 42
- Transporting the heat pump 43
- Positioning the heat pump 43
- Maximum working temperatures 43
- Minimum working temperatures 43
- Fit the particle fi lter 43
- Collector hose 44
- Heat carrier pump 52
- Connecting the heat pump to 62
- General alarm 64
- External input 64
- Load monitor 64
- Commissioning the heat pump 66
- Temperature settings 67
- Hot water settings 67
- Commiss./Service 67
- Timer readings 68
- Setting the additional heat 69
- Return to factory settings 69
- Drying program for fl oor tile 70
- Commissioning report 72
- Technical information 74
- TECHNICAL INFORMATION 75
Related products and manuals for Heat pumps Bosch EHP 6-11 LW
Heat pumps Bosch 7 KW Instruction Manual
(49 pages)
(49 pages)
Heat pumps Bosch 11 KW User Manual
(12 pages)
(12 pages)
Heat pumps Bosch SM048 Specifications
(41 pages)
(41 pages)
Heat pumps Bosch SM024 Specifications
(96 pages)
(96 pages)
Heat pumps Bosch SM024 Installation Manual
(20 pages)
(20 pages)
Heat pumps Bosch SM070 Specifications
(100 pages)
(100 pages)
Heat pumps Bosch EHP 6.5 AA User Manual
(84 pages)
(84 pages)
Heat pumps Bosch CP009 User Manual
(150 pages)
(150 pages)
Heat pumps Bosch SM024 Specifications
(41 pages)
(41 pages)
Heat pumps Bosch SM024 Specifications
(32 pages)
(32 pages)
Heat pumps Bosch TW Series Specifications
(24 pages)
(24 pages)
Heat pumps Bosch 7739832071 Brochure
(8 pages)
(8 pages)
Heat pumps Bosch BOVA-36HN1-M18M User Manual
(44 pages)
(44 pages)
© 2020, manymanuals.com. All rights reserved. | 0.906 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals