Bosch D1255RB Installation Guide Page 18
- Page / 104
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV2/D7412GV2 | Operation and Installation Guide | 4.0 Installation
18 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
4.5.5 Locking the Reset Pin
Locking the reset pin disables the control panel
(Figure 6). When the control panel is disabled, the
system ignores the keypads and points. CALL FOR
SERVICE appears in keypad displays when the pin is
locked down.
On-board relays (Terminals 6 and 7) and off-board
relays deactivate when the control panel is reset.
Terminal 8 has power when the relay is deactivated.
Activation interrupts power at that terminal. The on-
board relay (Terminal 8) remains deactivated when
the reset pin is locked in the disable position.
Releasing the reset pin from the closed position
resets the control panel. The control panel resets all
its timers, counters, indexes, and buffers. Any points
that restore after a reset do not generate Restoral
Reports.
If the reset pin is placed in the disable position when
all areas are armed, there must be an entry in the
Answer Armed program item. Refer to RPS
Parameters in the D9412GV2/D7412GV2 Program
Entry Guide
(P/N: F01U003636).
Locking the pin in the disable position applies power
to the control panel and charges the battery while the
detection devices and keypads are installed.
Figure 6: Reset Pin
Reset Pin
Disable All Except Battery
Charging And Programming
PERIPHERAL DEVICE CONNECTIONS
RED POWER +
YELLOW DATA BUS A
GREEN DATA BUS B
BLACK COMMON
32
31
30
29
1
2
1 - Reset pin locked (closed).
2 - Reset pin normal (open).
4.6 Completing the Installation
If not already complete, make the earth ground
connection to Terminal 10 and lock the reset pin in
the closed position.
4.6.1 Charging the Battery
Connect the battery, then the transformer to allow the
control panel to charge the battery while you complete
the installation. Refer to Section 5.0 Power Supply on
page 23 for instructions.
On-board Buzzer Sounds at Power Up and Reset:
The system performs a series of self-diagnostic tests
of hardware, software, and programming at power up
and at reset. The buzzer on the control panel sounds
during the tests. The self-diagnostics tests complete
in approximately 1 to 3 seconds.
If the control panel fails any test, the buzzer continues
sounding and a System Trouble message appears at
the keypads. Refer to Problems Found during Self
Diagnostics in the D9412GV2/D7412GV2/D7212GV2
Installation and Troubleshooting Quick Reference
Guide (P/N: F01U003638) for a description of each
system trouble message.
Touch Terminal 10 First: If the on-board buzzer
sounds briefly when the control panel is touched, any
static charge you carry discharges to the control
panel.
Avoid electrostatic discharge. Always
touch Terminal 10, the earth ground
connection, before beginning work on the
control panel.
If the control panel receives an electrostatic
discharge, it might generate Watchdog Reset and
Param Fail events.
4.6.2 Installing and Wiring Detection Devices
Install and wire detection devices and keypads at their
locations throughout the premises. Do not connect
the control panel yet.
Section 8.0 On-Board Points on page 35 contains
instructions for wiring the on-board points to detection
devices. Section 11.0 Arming Devices on page 58
contains instructions for wiring the keypads.
Instructions for wiring the off-board point POPIT
sensor loops are found in the instructions packaged
with the POPIT modules.
- D9412GV2 1
- D7412GV2 1
- Trademarks 2
- Certifications and Approvals 2
- Listings and Approvals 2
- Federal Communications 2
- Commission (FCC) Rules 2
- Contents 4
- 1.0 Introduction 7
- 2.0 Lightning Strikes 8
- 3.0 Overview 9
- 3.2 Accessories 10
- 4.0 Installation 15
- 4.5 Connecting Earth Ground 16
- Reset Pin 18
- Disable All Except Battery 18
- Charging And Programming 18
- 4.9 Testing the System 19
- 4.10 Service Walk Test 20
- 5.0 Power Supply 23
- LEDs Off When Normal 26
- Charging Status 26
- Low Battery 26
- 6.0 Power Outputs 28
- 1.4 A − NSC current 29
- Alarm current 29
- 7.1 Registration 30
- 7.2 Notification 30
- 7.3 Location 30
- Phone Cord Length 33
- D161 2.4 m (8 ft) 33
- D162 61 cm (2 ft) 33
- 8.2 Point Sensor Loops 35
- 8.3 Point Parameters 35
- 8.4 Point Response Time 36
- Using the Rothenbuhler 36
- 0.64 mm (1/4 in.) 37
- RED ORG WHT BL K 38
- 9.0 Off-Board Points 39
- Modules 40
- D9127U/TD9127U/T 41
- D9127U/T 41
- 23451 678 46
- S3 Option 49
- NOT USED 50
- NEX POWER + 50
- COMMON 23 50
- COM IN OUT+12V 51
- 9.5 Testing Off-Board Points 52
- 10.0 Off-Board Relays 53
- 1 2 3 4 567 8 54
- 11.0 Arming Devices 58
- 11.4 Keyswitch 60
- 12.0 SDI Devices 62
- 12.5 SDI Address 80 63
- 12.6 SDI Address 88 64
- 13.1 Programmer Connector 66
- 13.3 Accessory Connector 66
- A.1 D9412GV2 Control Panel 69
- Point 1 Point 2 70
- Point 3 Point 4 70
- Point 5 Point 6 70
- Point 7 Point 8 70
- A.2 D7412GV2 Control Panel 72
- Specifications 77
- Bosch Security Systems, Inc 78
- 130 Perinton Parkway 78
- Fairport, NY 14450-9199 78
- D1255/D1255B 79
- 1.0 Description 80
- 2.0 Digital Keypad 81
- 3.0 Installation 82
- 4.0 Specifications 83
- Bosch Security Systems 86
- DS1101i/1102i/1108i 87
- Glass Breakage Detectors 87
- Alarm/Test LED 88
- 48781-01 91
- PIR Signal 92
- Intrusion Detector 93
- Installationsanleitungen 96
- 㹿ࡼ㑶㒓⌟఼ᖂ 100
- ⊶ܹ։⌟఼ᅝ㺙䇈ᯢ 100
- Installation Instructions 101
- 6.0 LED Operation 102
- 9.0 Supervision Features 103
- 11.0 Coverage Pattern 104
- 10.0 Other Information 104
Related products and manuals for Numeric keypads Bosch D1255RB
(7 pages)© 2020, manymanuals.com. All rights reserved. | 0.550 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals