Bosch D1255RB Installation Guide download pdf (Page 19)

D9412GV2/D7412GV2 | Operation and Installation Guide | 4.0 Installation

Bosch Security Systems, Inc. | 7/09 | F01U003641-04 19

4.6.3 Installing Modules and Relays

1. Power down the unit by unplugging the

transformer and disconnecting the battery.

Always power down the unit when

installing modules or relays, or when

making wiring connections to the control

panel.

2. Install and wire any modules required for the

installation as described in the module’s

installation instructions.

Instructions for the D8125 POPEX Module,

D8128D OctoPOPIT Module, D8129 OctoRelay

Module, D811 Arm Status Relay Module, and

D928 Dual Phone Line Switcher appear in this

guide.

Refer to Section 9.0 Off-Board Points on page

39 for D8125 and D8128D instructions. Refer to

Section 10.0 Off-Board Relays on page 53 for

D8129 and D811 instructions. Refer to Section

7.11 D928 Dual Phone Line Switcher on page 32

for D928 instructions.

3. If using the power outputs at Terminals 7 or 8,

refer to Section 6.4 Programmable Power Output

Terminals 6, 7, and 8 on page 28 for

instructions.

4.6.4 Connecting the On-board Points and

Keypads

Connect the on-board points and keypad wiring to the

system. Refer to Section 8.0 On-Board Points on

page 35 and Section 11.0 Arming Devices on page 58

for instructions.

4.6.5 Powering Up

Reconnect the battery, then plug in the transformer.

The buzzer sounds for two seconds when the control

panel is powered up. Leave the reset pin in the locked

position.

Yellow Charging Status LED Remains Lit: If the

yellow charging status LED remains lit after five

minutes of powering up the control panel, either the

battery is deeply discharged or too many powered

devices were connected to the control panel.

Combined continuous current draw for Terminals 3, 8,

24, and 32, and the accessory connector cannot

exceed 1.4 A. Refer to Section 6.0 Power Outputs on

page 28 for help.

4.7 Programming the Control Panel

If the control panel is not already programmed, review

the D9412GV2/D7412GV2 Program Entry Guide

(P/N: F01U003636). Ensure that all accessory

modules for desired features are available for

installation. Place the reset pin in the locked position

to copy or send information to and from the control

panel.

Use the D5200 Programmer or the RPS to load a

custom program into the control panel.

Move the reset pin to the normal position refer to

(Figure 6 on page 18). The control panel sends

Reboot and Battery Reports to the receiver if

programmed for reporting.

4.8 Installing the Point Chart Label

The point chart label is required for fire

systems with verifications points.

A point chart label is included in the literature pack.

Install the point chart label for fire or combined fire-

and-burglary systems that use verification points.

Use the D9412GV2/D7412GV2 Program Record

Sheet (P/N: F01U003635) to gather the necessary

information for completing the point chart. Fill out the

label and install it on the inside of the enclosure door

(refer to Figure 2 on page 15).

Avoid smearing the entries on the chart.

Use the peel-off backing to press the

label in place.

4.9 Testing the System

After installing and programming the control panel,

test the system completely. Test the control panel and

all devices for proper operation.

Test after initially programming the control

panel.

To meet UL 864 requirements, perform a

full system test after any subsequent

programming session.

Refer to Section 4.10 Service Walk Test on page 20

for complete Service Walk Test instructions.

Clear after Test: To clear the event memory and

report buffer, momentarily close the reset pin. Events

stored in the control panel’s event log are not cleared.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 103 104

Comments to this Manuals

No comments

Bosch D1255RB Installation Guide Page 19

Comments to this Manuals

Related products and manuals for Numeric keypads Bosch D1255RB