Bosch GSS 280 AE Operations Instructions download pdf (Page 13)

English - 3

Sanding Sheets without Velcro Backing

(see figure )

Lightly lift the clamping lever 6 and unlatch it.

Slide the sanding sheet 13 under the open

clamping bracket 8 (

➊) and reinsert the clamping

lever 6 (

➋).

Make sure that the sanding sheet 13 faces firmly

against the sanding plate. Fold the sanding sheet

around and clamp the other end in the same

manner.

Sanding sheets without holes, e. g. from rolls or

by the meter, can be punctured with the perforat-

ing tool 22* for use with dust extraction (see

figure ).

The standard sanding plate 7 with velcro backing

can be exchanged against various specialty

sanding plates (accessories).

For this, unscrew the six screws 23 with a screw-

driver and remove the sanding plate.

Attach the desired sanding plate and insert

screws 23, or 26 respectively, when using the

thin, extended sanding plate 24.

External Dust Extraction

(see figure )

Slide the extraction adapter 15 onto the outlet

piece 16 and make sure that the latches engage.

To remove, press the latches together at the rear

and pull off the extraction adapter.

The vacuum cleaner must be suitable for the ma-

terial to be worked.

When vacuuming dry dust that is especially detri-

mental to health or carcinogenic, use a special

vacuum cleaner.

Dust Bag (see figure )

For clean working, a dust bag 18 (accessory) can

be used.

Pull out the plastic slider 17 at the bottom side of

the handle completely and attach the dust bag 18

onto the extraction neck. The plastic slider 17

must be inserted into the holder on the dust box.

Internal Vacuuming with Dust Box

(see figure )

Attaching the dust box:

Before assembling the dust box 5, pull out the

plastic wedge 17. Place the dust container onto

the outlet piece 16 and allow it to notch; make

sure that the holder 19 grips the plastic

wedge 17.

Emptying the dust box:

Actuate the latching lever 20 and pull off the dust

box 5 toward the bottom.

Before opening the dust box 5, it is recom-

mended to loosen the dust from the filter element

by gently striking it against a firm support.

Grasp the dustbox by the recessed grip, fold the

filter element (micro filtersystem) 21 upwards and

empty the dust box 5. Clean the thin plates of the

filter system with a soft brush.

Observe correct mains voltage: The voltage of

the power source must agree with the voltage

specified on the nameplate of the machine.

Equipment marked with 230 V can also be con-

nected to 220 V.

Switching On and Off

To start the machine, press the On/Off switch 3

and keep it depressed.

Lock the pushed On/Off switch 3 by pressing the

lock-on button 4.

To switch off the machine, release the On/Off

switch 3 or, when locked on with the lock-on but-

ton 4, briefly press the On/Off switch 3 and then

release.

Oscillating Rate Selection

(GSS 230 AE/GSS 280 AE)

With the knob 2, the required oscillation rate can

be selected (also while running).

The required oscillation rate is dependent on the

material and is to be determined by a practical

trial (See the applications table at the end of the

operating instructions).

After longer periods of working at low speed, al-

low the machine to cool down by running it for ap-

prox. 3 minutes at maximum speed with no load.

Replacing the Sanding Plate

(see figure )

Dust/Chip Extraction

Starting Operation

E1-E4

2 609 932 440.book Seite 3 Montag, 13. Dezember 2004 11:06 11

13 • 2 609 932 440 • TMS • 03.12.04

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 69 70

Comments to this Manuals

No comments

Bosch GSS 280 AE Operations Instructions Page 13

Comments to this Manuals

Related products and manuals for Power sanders Bosch GSS 280 AE