Bosch AutoDome Installation Manual Page 54
- Page / 84
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
44 en | Installing the In-Ceiling Mount AutoDome Modular Camera System
F01U010921 | 1.0 | 2006.10 Installation Manual Bosch Security Systems, Inc.
3.6 Wire the Interface Box
The Interface Box can be wired through the top or side. Use the supplied rubber plug to seal
the hole which will not be used to route wires.
Fig. 3.7 Interface Box Connections
After routing all video, control, power, and alarm wires:
1. Attach a 3/4-inch NPS (20-mm) conduit fitting to the hole in which you bring in the wires.
Be sure to thread the inside nut to the conduit fitting.
2. Route the video, control, power, and alarm wires through the conduit fitting and into the
Interface Box.
3. Cut and trim the wires allowing for sufficient slack to their respective terminals in the
box.
4. Attach the video and control data in/out wires to their respective terminals in the Inter-
face Box. See Table 3.1 on page 45 for terminal connections.
5. If using UTP for video or Ethernet, you must attach an RJ45 connector plug to the incom-
ing UTP cable and connect it to its matting connector J101 in the Interface Box. See
Chapter 4: Cable and Wire Standards for specifications.
6. Connect the 24 VAC power wires to the P101 connector in the Interface Box.
7. To connect alarm inputs and outputs, attach the supplied 6-pin Alarms In and the 4-pin
Alarms Out connector plugs with flying leads to the appropriate alarm wires. Then con-
nect the plugs to their mating connectors P103 and P102 in the Interface Box.
Fig. 3.8 Alarm and Relay Connector Plugs
8. To connect supervised alarms and relays, attach the appropriate wires to their terminals
on the P104 connector on the Pipe Interface Board. See Chapter 5: Alarms and Relay Con-
nections for more details on wiring alarms.
DATA IN/OUT
DATA IN/OUT
ALARM IN
P105
P105
P104
P104
P102
P103
ANALOG IN RELAY
ANALOG IN RELAY
ALARMS
OUT
J101
J101
J102
24VAC
24VAC
P101
SIG GND
SIG GND
TXD (-)
TXD (-)
RXD (+)
RXD (+)
+ C
+ C
- C
- C
NC
NC
NO
NO
COM
COM
AGND
AGND
A2
A2
A1
FIBER OPTICS
FIBER OPTICS
J103
J103
ETHERNET
OR UTP
VIDEO
DOME
POWER
COAX
VIDEO
A3
A4
A5
A6
A7
AGND
AGND
OUT3
OUT2
OUT1
i
NOTICE! If installing the dome to a drywall ceiling, allow enough wire to make the
connections in the Interface Box below the ceiling. See Figure 3.9 on page 45 for connector
locations and Table 3.1 on page 45 for wire connections.
4-PIN
ALARM OUT
CONNECTOR
6-PIN
ALARM IN
CONNECTOR
WHITE
ORANGE
BROWN
GREEN
WHITE
ORANGE
BROWN
GREEN
YELLOW
BLUE
ALARM OUT 1
ALARM IN 3
ALARM IN 4
ALARM IN 5
ALARM IN 6
ALARM IN 7
ALARM GROUND
ALARM OUT 2
ALARM OUT 3
ALARM GROUND
7-PIN RELAY CONNECTOR
N.O. COM
N.C.
A1 GND
A2
1- N.O.
2- COM
3- N.C.
4- EARTH GROUND
5- ANALOG ALARM 1
6- ANALOG ALARM 2
7- GROUND
* Low Voltage TTL (3.3V) can also be used.
- VG4 Series 1
- Audience 3
- Document Conventions 3
- Customer Support and Service 4
- Related Publications 4
- Table of Contents 5
- Important Safeguards 7
- FCC & ICES INFORMATION 9
- Safety Precautions 9
- INFORMATIONS FCC ET ICES 10
- Sécurité 10
- Enlèvement du capot 11
- 24 VAC Units 11
- (Pole) Mounts 13
- 1.1.2 Description 14
- 1.1.3 Tools Required 15
- 1.3 Mount Power Supply Box 16
- 24 VAC 17
- N.O. COM 18
- Power In 19
- Control Data 19
- POWER SUPPLY BOX 20
- PENDANT ARM 20
- FROM ARM 22
- HARNESS 22
- Fig. 1.11 Attach bubble 24
- 2.1 Unpacking 27
- 2.1.2 Description 28
- 2.1.3 Tools Required 29
- 2.3 Mount Power Supply Box 30
- 2.3.1 Attach Cover Door 31
- LINE NC NEUT 32
- LINE N 34
- CONTROL DATA 35
- AND VIDEO IN/OUT 35
- 10-24 SS Pan Head Screw 38
- 1/4 -20 SS Cap Screw 38
- Parapet Pipe Arm 38
- End Cap with O-Ring 38
- Down Pipe 38
- SET SCREW 39
- DOME CAP 39
- HREAD SEALANT 39
- 2.7 Wire Pipe Interface Board 41
- RETAINING SCREWS (3) 43
- PENDANT MOUNTING 43
- SCREWS (2) 43
- INTERFACE BOARD 43
- 3.1 Unpacking 49
- CAMERA MODULE 50
- DOME BUBBLE 50
- (CLEAR OR TINTED) 50
- IN-CEILING HOUSING 50
- INTERFACE MODULE 50
- 3.3 Dimensions 51
- 3.6 Wire the Interface Box 54
- 3.8 Secure Housing to Ceiling 57
- 3.10 Attach Bubble 59
- 24 V to AutoDome 61
- 1. Standard heater module 61
- 4.3 Video and Control Cables 62
- 4.4 Control-only Cables 64
- CPU MODULE BOARD 65
- LOCATION 66
- 5.1 Alarm Inputs 67
- ALARM INPUTS 1 TO 7 69
- DOME CONNECTOR 69
- 6Glossary 71
Related products and manuals for Bridge cameras Bosch AutoDome
Bridge cameras Bosch VJR SERIES User Manual
(28 pages)
(28 pages)
Bridge cameras Bosch NEI-Series User Manual
(124 pages)
(124 pages)
Bridge cameras Bosch EX36 Instruction Manual
(24 pages)
(24 pages)
Bridge cameras Bosch Camera User Manual
(5 pages)
(5 pages)
(40 pages)
Bridge cameras Bosch AutoDome User Manual
(42 pages)
(42 pages)
© 2020, manymanuals.com. All rights reserved. | 0.399 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals