Bosch EnviroDome Installation Manual download pdf (Page 29)

Section 13

PTZ SETUP

(See FIGURE 13C for the PTZ SETUP menu hierarchy).

Autopan Speed – Adjusts speed of the camera during Auto Pan/ Auto Scan. The Factory Default setting is 30°/sec.

Choices: . . . . . . . . . . . . . .Sliding Scale from 1°/sec to 60°/sec.

Tour Period – Changes dwell time between Presets during a Preset Tour. The Factory Default setting is five sec.

Choices: . . . . . . . . . . . . . .Sliding Scale from 3 sec to 10 min.

PTZ Fixed Speed – Sets Pan/Tilt speed when controlled by a fixed speed controller. The Factory Default setting is four.

Choices: . . . . . . . . . . . . . .Sliding Scale from 1 (slow) to 15 (fast).

Inactivity – Selects the mode that the dome reverts to after the period of time specified in the Inactivity Period (next menu

option), without operator activity. The Factory Default setting is OFF.

Choices:

*Off . . . . . . . . . . . . . . . . . .Remains on current scene indefinitely.

Scene 1 . . . . . . . . . . . . .Returns to Preset 1.

Prev Aux . . . . . . . . . . . . .Returns to previous activity (previous activities include Aux commands 1, 2, 8, 50, 52).

Inactivity Period – The time period of inactivity before the above action occurs. Default setting is two min.

Choices: . . . . . . . . . . . . . .Sliding Scale from 3 sec to 10 min.

AutoPivot – AutoPivot automatically rotates the camera 180° when following a subject travelling directly beneath the camera.

The Factory Default setting is ON.

Choices:

*On . . . . . . . . . . . . . . . . . .Camera automatically pivots.

Off . . . . . . . . . . . . . . . . . .Camera stops tilting when looking straight down.

Restore Defaults – Use this to restore ALL choices for this submenu ONLY, back to the Factory Defaults.

Choices: . . . . . . . . . . . . . .Yes, No.

NOTE: The following two (2) PTZ SETUP options refer to AutoTrack models only, and will not appear on the screen otherwise.

AutoTrack Comms: – Enables/Disables the AutoTracker completely, including all communications.

Choices: . . . . . . . . . . . . .On (enable), Off (disable).

Camera Height: – Selects the height of the camera in relation to the surface being viewed.

Choices: . . . . . . . . . . . . .From 2.4 m to 30.7 m (8 ft to 100 ft); use the Joystick Up/Down to adjust.

DISPLAY SETUP

(See FIGURE 13D for DISPLAY SETUP menu hierarchy.)

Title OSD – Controls whether sector or shot title are displayed. The Factory Default setting is MOMENTARY.

Choices:

*Momentary . . . . . . . . . . .Titles are displayed for a few sec, then disappear from the screen.

On . . . . . . . . . . . . . . . . . . .Titles are displayed.

Off . . . . . . . . . . . . . . . . . . .Titles are hidden.

Camera OSD – Controls whether the camera information is displayed (such as digital zoom, Iris OPEN/close, etc.).

The Factory Default is ON.

Choices:

*On . . . . . . . . . . . . . . . . .Camera commands are displayed.

Off . . . . . . . . . . . . . . . . . . .Camera commands are hidden.

Display Adjust – Adjusts the vertical position of the on-screen display. See the on-screen display for instructions.

Sector Blanking – Selects sectors for video blanking. Sectors available are 1 to 16. See the on-screen display for

instructions.

Privacy Masking – Up to six (6) privacy masks are available to mask out sensitive areas.

Restore Defaults – Restores ALL choices for this submenu ONLY, back to the Factory Defaults.

Choices: . . . . . . . . . . . . . .Yes, No.

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 39 40

Comments to this Manuals

No comments

Bosch EnviroDome Installation Manual Page 29

Comments to this Manuals

Related products and manuals for Bridge cameras Bosch EnviroDome