Bosch AMAX panel 2000 ICP-AMAX-P Installation Manual Page 89
- Page / 92
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
AMAX panel 2000 / AMAX panel 2000 EN Troubleshooting | en 89
Bosch Sicherheitssysteme GmbH Installation Manual F.01U.241.127 | V4 | 2011.12
11 Troubleshooting
Trouble Causes & Measures
No immediate response
from zone testing right
after powered up.
– To work normally, operate the system one minute after
powered up.
No indication on keypad
after powered up.
– Check that the AC Mains power and battery fuse are
correctly connected and work normally.
– Check the Bosch Bus RBGY are correctly connected.
No response from the
keypad (Press any key
sounds error).
– Check the Bosch Bus RBGY are correctly connected.
– Enter wrong code more than limit, the keypad is lockout for
3 minutes.
– Wrong jumper in using two keypads at the same time.
– When one keypad is used, the other one can be used only
30 seconds later.
Can not enter into
programming mode after
powered up.
– Control Panel is in alarm state. E.g. Switch tamper or 24-
Hour zone is still not ready.
– Control Panel is in arming state. Programming mode can
only be operated in disarming state.
– Installer is not enabled from User
No indication on on-board
LED .
– AC Mains power or the battery is failed. Restore the power.
– The board is damaged. Change a new one.
Zone Leds are always on. – Check that the zones are correctly connected.
– Check that the sensors work normally.
– Check that the EOL resistor is correctly connected with the
sensor.
Fault Led is always on /
flashing.
– Time and date are not set.
– No battery or the battery is lower than 12V.
– No siren ( >1,2 K resistor can replace the siren).
– Telephone number is not correctly programmed.
– Not connect with the telephone network.
– Switch tamper is not connected. Otherwise the short
jumper is connected.
– Some plug-in module is not used in programming, such as
DX3010, DX4020 or DX4020G. Refer to Installation Guide
for detailed measures.
AC Mains power fuse is
broken.
– Check the transformer 18V wire is correct.
Over current protection in
Aux power.
– Check the 12V Aux power wiring is correct.
– Check if the Aux power service is higher than 900mA ( top
limit to control panel). If so, the peripheral is supplied by
additional power supply.
Aux power can not
restore after short
circuited.
– Restart the AC Mains power and battery.
- ICP-AMAX-P / ICP-AMAX-P-EN 1
- 1 Graphics 3
- 4 ICP-AMAX-P / ICP-AMAX-P-EN 4
- Table of Contents 5
- 1 Short Information 10
- 2 System Overview 11
- 3 Installation 12
- ICP-AMAX-P 13
- ICP-AMAX-P-EN 13
- 3.3 Programming 14
- Table 3.2 Keypad Indicators 15
- Figure 3.3 17
- Figure 3.2 17
- Figure 3.4 18
- 4User Guide 19
- 1 2 3 … 20
- Table 4.3 Keypad sounds 21
- 4.1 Arming the System 22
- 4.1.2 Arming in STAY mode 23
- 4.2 Disarming the System 24
- 4.4 Walk test mode 25
- 4.5 Event Memory Recall mode 25
- 4.6 Reset the Control Panel 26
- 4.7 Bypassing 26
- 4.9 Change individual code 27
- 4.11 Domestic Dialing 28
- 5.1 Accessory Modules Fail 30
- 5.1.2 Keypad 2 fail 31
- 5.1.3 DX3010 Fail 31
- 5.2 Power Faults 32
- 5.3 Warning Device Failure 33
- 5.4 Telephone Line Fault 34
- 5.5 Date and Time Fail 35
- 5.6 Communication Failure 35
- 5.7 Tamper Condition 36
- 5.7.4 Keypad lock out 37
- 5.7.5 Sensor Tamper 37
- 5.7.6 Zone Tamper 37
- 5.8 External Fault 38
- 6 System Functions 39
- 6.2 Siren Test 40
- 6.4 View date and time 40
- 6.5 Walk Test Mode 40
- 6.6 Event Memory Recall Mode 41
- 6.7 Reset panel/clear siren 41
- 6.8 Initiate a Modem Call 42
- 6.9 Send Test Report 42
- 6.10 Bypass Zones 42
- 6.11 Show Zone Type 42
- 6.14 Change individual code 43
- 6.15 Setting date and time 43
- 6.16 Add/delete User Codes 44
- 6.19 Enter Programming Mode 45
- 7 System Informations 1 48
- 7.4 Software 49
- 7.5 Domestic Dialing 50
- 7.6 Reporting Formats 50
- 7.7 Dialer Information 51
- Table 7.1 Dialing Digits 52
- 7.8 Access Codes 54
- 7.8.3 User Codes 55
- 8 System Informations 2 56
- BBBBB7DPSHU6ZLWFK 57
- BBBBB=RQH6ZLWFK 57
- 8.1.4 Zone Bypass 62
- 8.1.5 Forced Arming 62
- 8.1.6 Silent Alarm 62
- 8.1.7 Zone Lockout 62
- 8.1.8 Zone Tamper 63
- 8.1.9 Zone Fault 63
- 8.1.10 Zone Report 63
- 8.1.11 Zone Chime Mode 63
- 8.2.3 Auto Test Report 68
- 8.4 Output Process 69
- 8.5 System Event Time 72
- 8.6 Optional Equipment 73
- 9 Technical Data 75
- 9.2 Interface Description 77
- 10 Programming sheets 78
- 10.1.2 Domestic Programming 79
- 10.2.1 Report Options 79
- 10.4 Zone Programming 82
- 10.5 Output Programming 85
- 10.6.1 Installer code 87
- 10.6.2 User Codes 87
- 11 Troubleshooting 89
Related products and manuals for Security access control systems Bosch AMAX panel 2000 ICP-AMAX-P
(8 pages)© 2020, manymanuals.com. All rights reserved. | 0.715 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals