Bosch AHS 54-20 LI Instruction Manual download pdf (Page 26)

26 | English

F 016 L70 590 | (30.6.09) Bosch Power Tools

Switching On (see figure B)

n Press and hold the On/Off switch 6 on the

rear handle.

o Then press the front On/Off switch 4.

Switching Off

Release the front 4 or rear 6 On/Off switch.

Working Advice (see figures C–E)

f Warning: Hold the hedgecutter away from

yourself using both hands. Stand in a se-

cure and stable position.

Cuts stems up to 20 mm in thickness (max.), up

to 25 mm in thickness (max.) at the tip end of

the blade.

When cutting, move steadily along the line of

cut, so that stems are fed directly into the cutter

blades. The double edge cutting blade enables

cutting in either direction, or with a side to side

motion.

Cut the sides of the hedge first, then the top.

To cut the sides straightly, we recommend cut-

ting from bottom to top in the direction of

growth. Younger stems tend to move outwards

when cutting them from top to bottom, resulting

in shallow patches or holes in the hedge.

To reach a level finish, fasten a piece of string

along the length of the hedge at the required

height and use as an alignment guide. Cut the

hedge just above the string.

In order to encourage strong, healthy growth of

your hedge, it is recommended when trimming

the top, to use the Collecto “clippings-collec-

tion” device (accessory).

This accessory conveniently gathers the clip-

pings as you cut, allowing them to be easily

tipped into a bag or sheet placed alongside the

hedge, and thus preventing cut clippings from

falling into the hedge.

Always take care to avoid cutting into objects

such as wire, which could cause damage to the

cutting blades and the drive.

Anti Blocking

The garden product has a patented feature

which works as follows:

If the blade stalls on a tough material, the load

of the motor increases. The intelligent micro-

electronics senses this overload condition and

repeatedly reverses the motor, in order to pre-

vent stalling and to cut the material through.

This audible reversing cut action continues for

up to 3 s.

After cutting through, the garden product con-

tinues in its normal mode, or in case the over-

load condition continues the blades automati-

cally stop in the open position (e. g. in case a

piece of metal fence accidentally blocks the gar-

den product).

Sawing Function (see figure F)

Although the blade gap allow wood to be cut up-

to Ø 20 mm, the tip of the blade is designed to

cut wood up to Ø 25 mm.

Battery Charge-control Indication

The battery 8 is equipped with a charge-control

indicator 16 which indicates its charge condi-

tion. The charge-control indicator 16 consists of

3 green LEDs.

Press the button 15 to actuate the charge-con-

trol indicator 16. After approx. 5 seconds, the

charge-control indicator goes out automatically.

The charge condition can also be checked when

the battery is removed.

When no LED lights up after actuating the but-

ton 15, the battery is defective and must be re-

placed.

For safety reasons, the charge condition of the

battery can only be checked when the garden

product is at a standstill.

LED Indicators Battery Capacity

Continuous lighting

of 3 green LEDs ≥ 2/3

Continuous lighting

of 2 green LEDs ≥ 1/3

Continuous lighting

of 1 green LED ≤ 1/3

Flashing of 1 green LED Reserve

OBJ_BUCH-948-003.book Page 26 Tuesday, June 30, 2009 2:04 PM

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 163 164

Comments to this Manuals

No comments