Bosch D1257 Installation Guide Page 124
- Page / 154
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV3/D7412GV3 | Program Entry Guide | EN | 124
Bosch Security Systems, Inc. | 10/11 | F01U170807-02
S## Holiday #
Default: None
Selection: Yes or No
Yes Use Holiday Index 1 with this sked.
No
Do not use Holiday Index 1 with this
sked.
4.3 Holiday Indexes
This programming module has two sections:
Add/Change/Delete and View Holidays. Use the
Add/Change/Delete section to program the Holiday
Indexes. The View Holidays section is a view-only
section provided for your convenience. Use View
Holidays to review the dates programmed in the
Holiday Indexes.
4.3.1 Add/Change/Delete
Program the dates for each of the Holiday Indexes.
You can program up to four Holiday Indexes in the
control panel. Within each index, you can select up to
365 dates to be designated as holidays.
The Holiday Indexes function independently of each
other. The same day can be programmed in all four
schedules. Holiday Indexes are used in programming
O/C Windows, User Access Windows, and skeds.
Date
Default: _ _ / _ _
Selection: MM/DD (month and date)
This entry selects the month and day you are
designating as a holiday.
To delete the date completely, select No for all of the
Holiday Index # entries.
Holiday Index #
Default: None
Selection: Select Dates from the Calendar
- Control Panels 1
- System Requirements 2
- Trademarks 2
- Documentation Conventions 2
- Table of Contents 3
- 1.0 Introduction 5
- 2.0 Panel and Area Wide 12
- Parameters 12
- 2.2 Phone Parameters 14
- DTMF Dialing 15
- Phone Supv Time 16
- Alarm On Fail 16
- Buzz on Fail 16
- Two Phone Lines 16
- 2.3 Routing 17
- Path 1 2 3 4 18
- SDI 88 88 89 90 91 18
- SDI 92 92 93 94 95 18
- R# Primary Device 19
- R# Backup Device 20
- Fire Reports 21
- Burglar Reports 21
- User Reports 22
- Test Reports 22
- Diagnostics Reports 23
- Relay Reports 24
- Auto Function Reports 25
- RPS Reports 25
- Point Reports 26
- User Chng Reports 26
- Access Reports 27
- 2.4 Power Supervision 29
- 2.5 Printer Parameters 30
- 2.6 RPS Parameters 32
- Log % Full 33
- Contact RPS if Log % Full 33
- RPS Call Back 34
- RPS Line Monitor 34
- Answer Armed 34
- Answer Disarmed 34
- RPS Phone # 35
- RPS Modem Speed 35
- 2.7 Miscellaneous 36
- 2.8 Area Parameters 36
- Area# Account Number 37
- A# Force Arm/Bypass Max 37
- A# Delay Restorals 38
- A# Exit Tone 38
- A# Exit Dly Time 38
- A# Auto Watch 38
- A# Verify Time 38
- A# Duress Enable 39
- A# Area Type 40
- A# Fire Time 42
- A# Fire Pattern 42
- A# Burg Time 42
- A# Burg Pattern 42
- A# Single Ring 43
- A# Bell Test 43
- A# Account O/C 44
- A# Area O/C 45
- A# Disable O/C in Window 45
- A# Auto Close 45
- A# Fail to Open 45
- A# Fail to Close 46
- A# Restrictd O/C 46
- A# Perimeter O/C 47
- A# Latest Close Time 47
- A# Two Man Rule 47
- A# Early Ambush 48
- A# Exit Restart 49
- A# Arm No Exit 49
- A# Exit Warning 49
- 2.9 Keypad (Command Center) 50
- CC# Supervised 51
- CC# Enhanced Command Center 51
- CC# Area Assign 51
- CC# Scope 52
- CC# A1 [through A#] in Scope 52
- CC# Enter Key Relay 53
- CC# Enter Key Cycle Door 53
- CC# Assign Door 53
- CC# Trouble Tone 54
- CC# Entry Tone 54
- CC# Exit Tone 54
- CC# Arm Now Warning 55
- CC# Close Door 55
- CC# Passcode Follows Scope 55
- CC# Scroll Lock 56
- CC# Menu Key Lock 56
- CC# Abort Display 56
- CC# Cancel Display 56
- Area# Is On 57
- Area# Not Ready 57
- Area# Is Off 57
- Area# Account Is On 57
- Area # Name Text 57
- Custom Function 58
- CF### Text 58
- CF### Key Strokes 58
- 2.10 User Interface 59
- Master Arm Delay 60
- Master Arm Instant 60
- Perimeter Instant 60
- Perimeter Delay 61
- Watch Mode 61
- Perimeter Partial 61
- View Area Stat 61
- Default Text 66
- Change Skeds 66
- Invisible Walk Test 66
- C Function 128 [through 143] 66
- Keypad Programming 66
- Authority Level 67
- L## Disarm 67
- L## View Memory 69
- L## View Point Status 69
- L## Walk Test 69
- L## Fire Test 69
- L## Send Report 70
- L## Door Control 70
- L## Cycle Door 70
- L## Unlock Door 70
- L## Secure Door 70
- L## Access Control Level 71
- L## Change Display 71
- L## Change Time/Date 71
- L## Change Passcode 71
- L## Default Text 74
- L## Change Skeds 74
- L## Invisible Walk Test 74
- L## Disarm Level 76
- L## Function Level 76
- 2.11 Function List 77
- 2.12 Relay Parameters 78
- A# Alarm Bell 79
- A# Fire Bell 79
- A# Reset Sensors 79
- A# Force Armed 80
- A# Watch Mode 80
- A# Area Armed 80
- A# Area Fault 80
- User ### 85
- U### Passcode 85
- U### User Group 85
- U### Name 86
- U### Mstr Site 86
- U### Mstr Crd Data 86
- U### SU1 through SU3 Site 86
- U### SU1 through SU3 C/D 86
- 3.0 Points 87
- (Continued on next page.) 89
- 3.2 Point Responses 91
- P## Pt Response 92
- P## Entry Delay 92
- P## Entry Tone Off 93
- P## Silent Bell 93
- P## Ring Until Restored 93
- P## Audible After 2 Failures 93
- P## Invisible Point 94
- P## Buzz On Fault 95
- P## Watch Point 96
- P## Relay Response Type 96
- P## Display as Device 96
- P## Local While Disarmed 96
- P## Local While Armed 97
- P## Disable Restorals 97
- P## Force Arm Returnable 97
- P## Bypass Returnable 98
- P## Bypassable 98
- P## Swinger Bypass 99
- P## Defer Bypass Report 99
- P## Cross Point 99
- P## Fire Point 100
- P## Alarm Verify 100
- P## Resettable 100
- 3.3 Point Assignments 101
- P### Area Assign 102
- P### Debounce 102
- P### Relay 103
- P### Point Text 103
- prompt on page 104
- prompt on page 103 104
- 4.0 Schedules (Skeds) 105
- W# Open Window Start 107
- W# Open Window Stop 107
- S M T W T F S 108
- W# Close Window Start 109
- W# Close Window Stop 109
- Start Stop 111
- Begin Start Stop 111
- 4.2 Schedules (Skeds) 114
- 4.3 Holiday Indexes 124
- 5.0 AUXPARM 125
- 5.4 SDI RPS Parameters 126
- Answer RPS Over Network 127
- RPS Address Verification 127
- Command 43, Remote Program 128
- Idle text 129
- RPS IP Address # 130
- RPS Port Number 130
- IP Addresses for Enhanced 131
- Communications 131
- Path # Poll Rate 132
- 220 230 240 250 260 270 134
- 5.6 SDI RPS/Enhanced 135
- Communications Configuration 135
- 5.7 Route Group Parameters 136
- 5.8 Miscellaneous 137
- Passcode Length 138
- Swinger Count 138
- Remote Warning 138
- Crystal Time Adjust 138
- 5.9 Cross Point Parameters 139
- 6.0 ACCESS CONTROL 140
- D#CC#Scope 141
- D# Custom Function 141
- D# Door Point 141
- D# Interlock Point 142
- D# Auto Door? 142
- D# Fire Unlock? 142
- 6.2 Strike Profile 143
- D# Buzz Time 144
- D# Extend Time 144
- D# Deactivate On Open? 144
- D# RTE Shunt Only? 144
- 6.3 Event Profile 145
- D# Enter Request? 146
- D# Exit Request? 146
Related products and manuals for Fire protection Bosch D1257
Fire protection Bosch FPC-500-8 User Manual
(40 pages)
(40 pages)
Fire protection Bosch D1257 Specifications
(24 pages)
(24 pages)
Fire protection Bosch FPC-500-4 User Manual
(34 pages)
(34 pages)
Fire protection Bosch D1257 User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.974 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals