Bosch D1257 Installation Guide Page 141
- Page / 154
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV3/D7412GV3 | Program Entry Guide | 6.0 ACCESS CONTROL EN | 141
Bosch Security Systems, Inc. | 10/11 | F01U170807-02
All SDI devices, regardless of area
assigned, report to Area 1, Account 1 by
default upon SDI failure. If a D9210B
becomes disconnected, an SDI Fail ##
and a Missing Point ### Event is
created.
If the D9210B is not programmed with a
D# Entry Area, 9210 NOT READY
appears at the keypad with this door
assigned to it when you press the
[ENTER] key.
D#CC#Scope
Default: 0
Selection: 0 to 8
1 to 8
Determines disarming rights. The
user’s access level and the CC #
Scope determines which areas are
disarmed.
0 Only the area assigned to the D#
Entry Area disarms this door.
Enter the keypad number (CC#) which determines
the scope of the user ID’s disarming rights. Areas
disarm on the basis of this keypad’s scope and the
authority level of the user.
The D# CC# Scope prompt is limited to
the first 8 keypads.
D# Custom Function
Default: 0 (Disabled)
Selection:
0, 128-143 (128-131 on the
D7412GV3)
0
Custom function disabled.
128-143 The custom function number that
executes upon a valid ID, given the
appropriate user access level and
area arm state.
You can program a custom function to run at the
keypad programmed for CC# Scope. This custom
function activates only for users with an L##
Function Level? Assignment (refer to Section 2.10
User Interface on page 76) in which a valid ID can
execute a custom function during the armed or
disarmed state. The user number to which the token
is assigned must have an assigned passcode.
If D# Disarm On Open is set to Yes for the same
door, and L## Function Level? is set to D or C, the
custom function executes when the door is physically
opened.
A user’s access level and the armed state
of the area determine whether the custom
function activates. This access level is
programmed in the L## Function Level?
prompt. Refer to 2.10 User Interface on
page 59.
Table 39 on page 141 shows how this programming
affects custom function activation.
Table 39: Effects of Programming on Custom
Function Activation
L## Function
Level?
Custom Function Activation
M
(Armed)
User token activates the custom
function assigned to the Door
Controller only while the entry area
for the Door Controller is Master
Armed or Perimeter Armed.
D
(Disarmed)
User token activates the custom
function assigned to the Door
Controller only while the entry area
for the Door Controller is disarmed.
C
(Armed and
Disarmed)
User token activates the custom
function assigned to the Door
Controller regardless of the armed
state of the entry area.
-
User token does not run the custom
function assigned to the Door
Controller.
A user’s security level must have an M,
P, or D to operate the custom function.
D# Door Point
Default: 0
Selection:
0 to 127, 129 to 247(0 to 75 on the
D7412GV3)
1 to 127,
129 to 247
The point number assigned to this
door. Points 128 and 248 are
reserved by the control panel for
internal use.
0
No point number is assigned to this
door.
Enter the point number assigned to this door. This
point cannot be used for any other point
assignments.
- Control Panels 1
- System Requirements 2
- Trademarks 2
- Documentation Conventions 2
- Table of Contents 3
- 1.0 Introduction 5
- 2.0 Panel and Area Wide 12
- Parameters 12
- 2.2 Phone Parameters 14
- DTMF Dialing 15
- Phone Supv Time 16
- Alarm On Fail 16
- Buzz on Fail 16
- Two Phone Lines 16
- 2.3 Routing 17
- Path 1 2 3 4 18
- SDI 88 88 89 90 91 18
- SDI 92 92 93 94 95 18
- R# Primary Device 19
- R# Backup Device 20
- Fire Reports 21
- Burglar Reports 21
- User Reports 22
- Test Reports 22
- Diagnostics Reports 23
- Relay Reports 24
- Auto Function Reports 25
- RPS Reports 25
- Point Reports 26
- User Chng Reports 26
- Access Reports 27
- 2.4 Power Supervision 29
- 2.5 Printer Parameters 30
- 2.6 RPS Parameters 32
- Log % Full 33
- Contact RPS if Log % Full 33
- RPS Call Back 34
- RPS Line Monitor 34
- Answer Armed 34
- Answer Disarmed 34
- RPS Phone # 35
- RPS Modem Speed 35
- 2.7 Miscellaneous 36
- 2.8 Area Parameters 36
- Area# Account Number 37
- A# Force Arm/Bypass Max 37
- A# Delay Restorals 38
- A# Exit Tone 38
- A# Exit Dly Time 38
- A# Auto Watch 38
- A# Verify Time 38
- A# Duress Enable 39
- A# Area Type 40
- A# Fire Time 42
- A# Fire Pattern 42
- A# Burg Time 42
- A# Burg Pattern 42
- A# Single Ring 43
- A# Bell Test 43
- A# Account O/C 44
- A# Area O/C 45
- A# Disable O/C in Window 45
- A# Auto Close 45
- A# Fail to Open 45
- A# Fail to Close 46
- A# Restrictd O/C 46
- A# Perimeter O/C 47
- A# Latest Close Time 47
- A# Two Man Rule 47
- A# Early Ambush 48
- A# Exit Restart 49
- A# Arm No Exit 49
- A# Exit Warning 49
- 2.9 Keypad (Command Center) 50
- CC# Supervised 51
- CC# Enhanced Command Center 51
- CC# Area Assign 51
- CC# Scope 52
- CC# A1 [through A#] in Scope 52
- CC# Enter Key Relay 53
- CC# Enter Key Cycle Door 53
- CC# Assign Door 53
- CC# Trouble Tone 54
- CC# Entry Tone 54
- CC# Exit Tone 54
- CC# Arm Now Warning 55
- CC# Close Door 55
- CC# Passcode Follows Scope 55
- CC# Scroll Lock 56
- CC# Menu Key Lock 56
- CC# Abort Display 56
- CC# Cancel Display 56
- Area# Is On 57
- Area# Not Ready 57
- Area# Is Off 57
- Area# Account Is On 57
- Area # Name Text 57
- Custom Function 58
- CF### Text 58
- CF### Key Strokes 58
- 2.10 User Interface 59
- Master Arm Delay 60
- Master Arm Instant 60
- Perimeter Instant 60
- Perimeter Delay 61
- Watch Mode 61
- Perimeter Partial 61
- View Area Stat 61
- Default Text 66
- Change Skeds 66
- Invisible Walk Test 66
- C Function 128 [through 143] 66
- Keypad Programming 66
- Authority Level 67
- L## Disarm 67
- L## View Memory 69
- L## View Point Status 69
- L## Walk Test 69
- L## Fire Test 69
- L## Send Report 70
- L## Door Control 70
- L## Cycle Door 70
- L## Unlock Door 70
- L## Secure Door 70
- L## Access Control Level 71
- L## Change Display 71
- L## Change Time/Date 71
- L## Change Passcode 71
- L## Default Text 74
- L## Change Skeds 74
- L## Invisible Walk Test 74
- L## Disarm Level 76
- L## Function Level 76
- 2.11 Function List 77
- 2.12 Relay Parameters 78
- A# Alarm Bell 79
- A# Fire Bell 79
- A# Reset Sensors 79
- A# Force Armed 80
- A# Watch Mode 80
- A# Area Armed 80
- A# Area Fault 80
- User ### 85
- U### Passcode 85
- U### User Group 85
- U### Name 86
- U### Mstr Site 86
- U### Mstr Crd Data 86
- U### SU1 through SU3 Site 86
- U### SU1 through SU3 C/D 86
- 3.0 Points 87
- (Continued on next page.) 89
- 3.2 Point Responses 91
- P## Pt Response 92
- P## Entry Delay 92
- P## Entry Tone Off 93
- P## Silent Bell 93
- P## Ring Until Restored 93
- P## Audible After 2 Failures 93
- P## Invisible Point 94
- P## Buzz On Fault 95
- P## Watch Point 96
- P## Relay Response Type 96
- P## Display as Device 96
- P## Local While Disarmed 96
- P## Local While Armed 97
- P## Disable Restorals 97
- P## Force Arm Returnable 97
- P## Bypass Returnable 98
- P## Bypassable 98
- P## Swinger Bypass 99
- P## Defer Bypass Report 99
- P## Cross Point 99
- P## Fire Point 100
- P## Alarm Verify 100
- P## Resettable 100
- 3.3 Point Assignments 101
- P### Area Assign 102
- P### Debounce 102
- P### Relay 103
- P### Point Text 103
- prompt on page 104
- prompt on page 103 104
- 4.0 Schedules (Skeds) 105
- W# Open Window Start 107
- W# Open Window Stop 107
- S M T W T F S 108
- W# Close Window Start 109
- W# Close Window Stop 109
- Start Stop 111
- Begin Start Stop 111
- 4.2 Schedules (Skeds) 114
- 4.3 Holiday Indexes 124
- 5.0 AUXPARM 125
- 5.4 SDI RPS Parameters 126
- Answer RPS Over Network 127
- RPS Address Verification 127
- Command 43, Remote Program 128
- Idle text 129
- RPS IP Address # 130
- RPS Port Number 130
- IP Addresses for Enhanced 131
- Communications 131
- Path # Poll Rate 132
- 220 230 240 250 260 270 134
- 5.6 SDI RPS/Enhanced 135
- Communications Configuration 135
- 5.7 Route Group Parameters 136
- 5.8 Miscellaneous 137
- Passcode Length 138
- Swinger Count 138
- Remote Warning 138
- Crystal Time Adjust 138
- 5.9 Cross Point Parameters 139
- 6.0 ACCESS CONTROL 140
- D#CC#Scope 141
- D# Custom Function 141
- D# Door Point 141
- D# Interlock Point 142
- D# Auto Door? 142
- D# Fire Unlock? 142
- 6.2 Strike Profile 143
- D# Buzz Time 144
- D# Extend Time 144
- D# Deactivate On Open? 144
- D# RTE Shunt Only? 144
- 6.3 Event Profile 145
- D# Enter Request? 146
- D# Exit Request? 146
Related products and manuals for Fire protection Bosch D1257
Fire protection Bosch FPC-500-8 User Manual
(40 pages)
(40 pages)
Fire protection Bosch D1257 Specifications
(24 pages)
(24 pages)
Fire protection Bosch FPC-500-4 User Manual
(34 pages)
(34 pages)
Fire protection Bosch D1257 User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 1.541 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals