Bosch CM8S Use and Care Manual download pdf (Page 37)



&.D#=2?.A6<;@

!.86;4.;BE696.?F2;02

Certain types of molding need a fence face extension

because of the size and position of the workpiece.

Holes are provided in the fence to attach an auxiliary

ence. The auxiliary fence is used with the saw in the 0°

bevel position only.

1. Use ¾” thick piece of wood (plywood is prefferd) to cut

an auxiliary fence based on dimensions shown in

Figure 49.

2. Place the auxiliary fence against the miter saw fence

(figure 48). Check that auxiliary fence does not

interfere with head assembly. Check for interference

between the auxiliary fence and the lower blade

guard. Make adjustments as necessary.

5208 3<? 6;A2?32?2;02 /2AD22;

.BE696.?F 32;02 .;1 @.D 52.1

0<:=<;2;2;A@ /F =2?3<?:6;4 . 1?F ?B; Fence

interference can prevent proper saw operation and

cause injury and/or tool damage.

3. Mark the locations of the support holes on the wood

from the back side of the fence (figure 48).

4. Drill and countersink the holes on the front of the

support board.

'<3.@A2;3?<:3?<;A<332;02

1. Attach auxiliary fence using four (4) 3/16" x 1-1/2"

long flat head machine bolts. Secure behind metal

fence with washer and #5 machine nuts.

2 .D.?2 <3 A52 =.A5 <3 A52 @.D

/9.12!.82.1?F?B;D6A5A52@.D

#33 /F 0<;1B0A6;4 . @6:B9.A21 0BAA6;4 0F092 .;1

</@2?C2A52=?<720A21=.A5<3A52@.D/9.1222=

5.;1@.A92.@A@6E6;052@.D.F3?<:A52=?<720A21

=.A5<3A52@.D/9.12

2. Make a full depth cut to create the blade slot.

'<3.@A2;3?<:/.08<332;02

Use minimum 3/4" thick auxiliary fence and 1/4" round

head wood screws (3/4" long).

1. Drill four pilot holes through auxiliary fence and run

screws from rear of metal fence.

2 .D.?2 <3 A52 =.A5 <3 A52 @.D

/9.12!.82.1?F?B;D6A5A52@.D

#33 /F 0<;1B0A6;4 . @6:B9.A21 0BAA6;4 0F092 .;1

</@2?C2A52=?<720A21=.A5<3A52@.D/9.1222=

5.;1@.A92.@A@6E6;052@.D.F3?<:A52=?<720A21

=.A5<3A52@.D/9.12

2. Make a full depth cut to create the blade slot.

9.A2.1!.056;2

&0?2D@

BE696.?F

2;02

9.12

&9<A

2-3/4”

5”

2-1/2”

4”

5-1/2”

1-1/2”

2” 2”

6”

1-1/2”

2-3/4”

17-1/4”

FIG. 48

FIG. 49

*%""

BE696.?F2;02

*%""

BM 2610025580 05-13_BM CM8S 5/17/13 1:37 PM Page 37

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 131 132

Comments to this Manuals

No comments

Bosch CM8S Use and Care Manual Page 37

Comments to this Manuals

Related products and manuals for Mitre saws Bosch CM8S