Bosch D7412G User Manual Page 42
- Page / 142
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412G/D7412G | Program Entry Guide | 2.0 9000MAIN EN | 42
Bosch Security Systems | 1/04 | 47775E
If a 24-hour point alarms while the area is
disarmed, arming that area with a
keyswitch does not clear the A# Single
Ring flag.
Silencing the bell resets A# Single Ring.
A# Bell Test
Default: No
Selection:
Yes or No
Yes Initiate Bell Test.
No Do not initiate Bell Test.
Provide alarm output from the relay programmed at
A# Alarm Bell
after the Closing Report was
confirmed or the exit delay time expired.
Bell Test After Confirmation
In areas that report opening and closing activity, the
Bell Test happens after the control panel sends the
Closing Report and receives the acknowledgment
from the central station receiver. For proper
operation of the Bell Test after closing confirmation,
the following rules apply:
• The control panel must report opening and
closings to the central station.
• Restricted openings and closings should not be
used, and Opening and Closing Windows
should not be used.
Area Armed Confirmation
In areas that do NOT report opening and closing
activity, the alarm bell relay output for this area is
activated for 2 seconds after exit time expires.
Multiple Bell Tests occur: When more than
one area is armed at the same time (such as
using the ARM ALL AREAS? function), the
bell rings for 2 seconds with a 2 second
pause between each bell activation if all
areas have the same exit delay time
programmed. Otherwise, the Bell Test
occurs as each area arms and it completes
its exit delay time.
When areas arm simultaneously and report
to the central station, the Bell Test occurs
as the central station receiver confirms each
area.
2.9.5 Open/Close Options
Programming determines if Opening, All Normal
Closing, and Force Arm/Bypass Closing Events are
reported to the remote central station. Without
remote reporting, all control panel and area arming
(Closing Events) and disarming (Opening Events)
default to local events.
Use this programming category to determine which
opening and closing supervision characteristics are
required.
There are three ways to generate reports from the
control panel. You can generate reports by account,
by area, or a combination of both.
To suppress reports:
• Use Opening/Closing Windows to suppress
reports for a specified period of time and then
automatically turn them on again.
• Use the Restricted O/C options. A Closing
Report is sent if the user is force arming, sending
duress, or bypass arming. An Opening Report is
sent if the user is disarming during an alarm
condition or unbypasses points when disarming.
If the system is normal, no Opening or Closing
Report is sent.
For the scheduled suppression of Opening
and Closing Reports, see Section 5.1.1
Opening and Closing) to define Opening
and Closing Windows.
Account Opening and Closing Reports
Opening and Closing Reports are sent by account
when the last area in a group of areas with the same
account number(s) is armed.
Area Opening and Closing Reports
Closing Reports are sent for each area as it is armed.
The account number is also sent for each area.
Customizing Account Opening and Closing
Reports
You can eliminate area Opening and Closing
Reports from selected areas in the account by
programming
A# Area O/C
No for those areas.
- D9412G/D7412G 1
- Trademarks 2
- Documentation Conventions 2
- Table of Contents 3
- 1.0 Introduction 5
- 1.4 New Features 6
- Table 3: continued 7
- 1.5 Product Handlers 8
- 1.6 Programming Options 8
- FILENAME 9
- NEWRECORD 9
- 2.0 9000MAIN 11
- 2.2 Phone Parameters 12
- DTMF Dialing 13
- Phone Supv Time 14
- Alarm On Fail 14
- Buzz on Fail 14
- Two Phone Lines 14
- 2.3 Routing 15
- R# Primary Device 17
- R# Backup Device 17
- View Events? 17
- Fire Reports 18
- Burglar Reports 18
- User Reports 19
- Test Reports 20
- Diag Reports 20
- Relay Reports 21
- AutoFunc Reports 21
- RAM Reports 22
- Point Reports 22
- 2.4 Enhanced Routing 23
- RG# Primary SDI 24
- RG# Backup SDI 24
- RG# Primary Pager 25
- 2.5 Power Supervision 27
- AC Fail/Res Rpt 28
- AC Tag Along 28
- 2.6 Printer Parameters 29
- 2.7 RAM Parameters 31
- RAM Passcode 32
- Log % Full 32
- RAM Call Back 32
- RAM Line Monitor 32
- Answer Armed 33
- Answer Disarmed 33
- 2.8 Miscellaneous 34
- 2.9 Area Parameters 34
- A# Acct Number 35
- A# FA Bypass Max 36
- A# Delay Res 36
- A# Exit Tone 36
- A# Exit Dly Time 36
- A# Auto Watch 37
- A# Verify Time 37
- A# Duress Enable 38
- A# Area Type 39
- D## CC# Scope 40
- A# Fire Pat 41
- A# Burg Time 41
- A# Burg Pat 41
- A# Single Ring 41
- A# Fire Time 41
- A# Bell Test 42
- A# Acct O/C 43
- A# Area O/C 44
- A# Disable O/C in Window 44
- A# Auto Close 44
- A# Fail to Open 44
- A# Fail to Close 45
- A# Restrictd O/C 45
- 2.10 Command Center 46
- CC# Supervised 47
- CC# Area Assign 47
- CC# Scope 47
- CC# A1[through A8] in Scope 48
- CC# Entr Key Rly 48
- CC# Entr Cycl Dr 48
- CC# Assign Door 49
- CC# Trouble Tone 49
- CC# Entry Tone 49
- CC# Exit Tone 49
- Program Record Sheet 50
- Area # Acct Is On 51
- Custom Function 51
- CF### Text 51
- CF### Key Strokes 52
- 2.11 User Interface 53
- P## Type 1 55
- Expand Test Rpt 55
- L## Access Level 56
- L## Disarm Level 56
- P## Bypassable 57
- P## FA Retrnable 57
- Bypass Returnable 57
- P## Resettable 57
- P## Type 58
- S## Time 58
- Authority Level 59
- L## Disarm 59
- L## Master Arm Delay 59
- .L## Mstr Arm Inst 59
- L## Fire Test 61
- L## Send Report 61
- L## Door Control 61
- L## Cycle Door 61
- L## Unlock Door 62
- L## Secure Door 62
- L## Access Ctl Lvl 62
- L## Passcode Disarm 66
- L## Security Level 66
- 2.12 Function List 67
- 2.13 Relay Parameters 67
- A# Alarm Bell 68
- A# Fire Bell 69
- A# Reset Sensors 69
- A# Force Armed 69
- A# Watch Mode 69
- A# Area Armed 70
- A# Area Fault 70
- A# Duress Relay 70
- A# Perim Fault 70
- A# Silent Alarm 70
- AC Failure 71
- Battery Trouble 71
- Phone Fail 71
- P## Type 0 72
- P## Fire 72
- 3.0 RADXUSR1/RADXUSR2 73
- User ### 74
- U### Passcode 74
- U### User Group 75
- U### Name 75
- U### Mstr Site 75
- U### Mstr C/D 76
- U### SU1 through SU3 Site 76
- U### SU1 through SU3 C/D 76
- 4.0 RADXPNTS 77
- P## Ent Tone Off 78
- P## Entry Delay 78
- Point Response 80
- Local Armed 80
- Local Disarmed 80
- P## Pt Response 82
- P## Silent Bell 83
- P## Ring Til Rst 83
- P## Audible After 2 Failures 84
- P## Invisible Pt 84
- P## Buzz On Fault 85
- P## Watch Point 85
- P## RlyResp Type 86
- P## Disp as Dvc 86
- P## Local While Disarmed 86
- P## Local While Armed 86
- P## Disable Rst 87
- P## BP Retrnable 87
- P## Swinger Byps 88
- P## Defer BP Report 89
- P## Cross Point 89
- P## Fire Point 90
- 4.2 Point Assignments 91
- P### Point Index 92
- P### Area Assign 92
- P### Debounce 92
- P### BFSK/Relay 93
- P### Point Text 93
- 4.3 COMMAND 7 and COMMAND 9 94
- 5.0 RADXSKED 95
- Early Begin 96
- W# Open Window Stop 97
- W# Close Early Begin 98
- W# Close Window Start 99
- W# Close Window Stop 99
- Xept Holiday 100
- W# Xept Holiday 100
- User Windows # 102
- UW# User Group 102
- 5.2 Skeds 104
- S## Function Code 105
- S## Area # 106
- Relay Number 106
- Cmd Center 108
- Custom Func 108
- 5.3 Holiday Indexes 113
- Holiday Index 1 114
- 6.0 RADXAUX1 115
- 6.4 SDI RAM Parameters 116
- Enable SDI RAM 117
- RAM IP Address 1 118
- RAM IP Address 2 118
- RAM IP Address 3 118
- RAM IP Address 4 118
- 6.5 Enhanced Communications 122
- Path # IP Add1 123
- Path # IP Add2 123
- Path # IP Add3 123
- Path # IP Add4 123
- 6.6 SDI RAM/Enhanced 125
- Communications Configuration 125
- Parity/Stop 126
- RTS Control 126
- DTR Control 126
- 9133 Supervision 126
- Base Port Number 126
- 6.7 Miscellaneous 127
- 6.8 Cross Point Parameters 128
- Cross Point Time 129
- 7.0 RADXAXS 131
- D# Interlock Point 132
- D# Auto Door? 132
- D# Fire Unlock? 132
- D# Disarm on Open? 132
- 7.2 Strike Profile 133
- 7.3 Event Profile 134
- D# Access Granted? 135
- D# No Entry? 135
- D# Enter Request? 135
- Programming Prompts 136
- Directory 136
- © 2003 Bosch Security Systems 142
Related products and manuals for Fire protection Bosch D7412G
Fire protection Bosch D9124 User Manual
(4 pages)
(4 pages)
Fire protection Bosch D9112 User Manual
(87 pages)
(87 pages)
Fire protection Bosch DS9400 User Manual
(8 pages)
(8 pages)
Fire protection Bosch FPD-7024 User Manual
(122 pages)
(122 pages)
Fire protection Bosch D7024 User Manual
(22 pages)
(22 pages)
Fire protection Bosch D9412GV2 User Manual
(74 pages)
(74 pages)
Fire protection Bosch D296/D297 User Manual
(12 pages)
(12 pages)
Fire protection Bosch D1257 Specifications
(16 pages)
(16 pages)
Fire protection Bosch D1256 User's Guide
(28 pages)
(28 pages)
Fire protection Bosch D1256 Specifications
(16 pages)
(16 pages)
Fire protection Bosch D1257 Installation Guide
(154 pages)
(154 pages)
© 2020, manymanuals.com. All rights reserved. | 0.310 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals