Bosch MIC SERIES 500 CAMERA 500 User Manual download pdf (Page 24)

24 en | Navigating the Menus MIC Series 500 Camera

F.01U.173.601 | 2.0 | 2010.11 User’s Manual Bosch Security Systems, Inc.

5.1 MIC Setups Menu

This section contains some of the more commonly modified settings for the MIC 500 Series

Camera. Pressing right on an option changes the highlight color to green and allows the

modification of the current setting value.

MAIN MENU 1/2 MIC SETUPS 1/2 MIC SETUPS 2/2

MIC SETUPS CONFIG UPRIGHT DIGITAL ZOOM ON

ACTIVATE FEATURE AUTO FLIP OFF

PRESET TOUR AUTO HOME ON SELF DIAGNOSIS

PATTERN TOUR HOME TO PRESET

PRESETS WASH-WIPE OFF

COMMUNICATIONS OSD OFF

ADVANCED SETUPS POS DISPLAY OFF

ALARMS AUTO ALARM OFF

Menu Item Description

CONFIG Available only via the menu see Section 5.1.1 Config Mode, page 26.

AUTO HOME Enables the unit to remain stationary when set to OFF or until the next user input. With Auto

Home turned on, the MIC 500 Series Camera can be can be configured to either move to the

home position (preset 1), start preset tour 1, or play pattern tour 1 using the “Home To”

setting. The amount of time before this takes place can be set to 30 seconds, 1 minute, 5

minutes, or 1 hour using the “Home Time” Setting in “Advanced Controls.”

HOME TO

WASH-WIPE Upon activation, the camera moves to a saved position (Wash Wipe Position, Advanced

settings), which should be set to look at the washer nozzle, starts the washer pump, and turns

the wiper on. Once released, the unit returns to its original position, stops the washer pump,

and continues wiping for a few seconds. This process only takes place if the Wash Wipe

command is turned on; otherwise, the camera just activates the washer pump and will not

move. If use of an external washer is required, then either the MIC-WKT (washer nozzle and

bracket and MIC-WSH card) or MIC-WKT-IR (washer nozzle and bracket) kits should be

purchased to enable a third party washer pump to be installed (see separate MIC-WKT manual).

OSD (on-screen

display)

Displays the camera module information icons on the video, such as zoom position, white

balance mode, shutter speed etc. This is only displayed when there are no captions on the

screen.

POS DISPLAY Indicates the current heading in degrees of the MIC 500 Series Camera in pan and tilt relative to

its zero position, this is set during installation. The MIC 500 Series Camera takes 0° as North, so

when the MIC 500 Series Camera is installed ensure the unit is pointed towards North, on a

level tilt, then use “Set Zero Pos” in “Advanced Controls.” When activated, the position display

shows the current compass heading North, South, East or West in a 1 or 2 character code N,

NW, W, SW, S etc, along with an accurate pan and tilt bearing. The display is shown in white

and resembles “N PAN: 125 TILT: 10."

AUTO ALARM Enables use for both single or multi alarm functionality. With Auto Alarm on, the MIC moves to

the Auto Alarm position (as configured using Cam-set, or “Alarms” - “Learn Alarm Pos”) upon

detection of a tamper line input. If Auto Alarm is turned off, the MIC 500 Series Camera ignores

any change in status of the tamper line which terminates in the MIC power supply, see MIC

power supply manual for further details.

DIGITAL ZOOM Provides both optical and digital zoom. On some systems, there is the option of selecting digital

zoom, however with others the control system always outputs commands to continue into

digital zoom which may not always be desirable. To stop this, there is an override function,

Digital Zoom, which if turned off will not go into digital no matter what the keyboard sends out,

and if activated will allow digital zoom as the controller dictates.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 55 56

Comments to this Manuals

No comments

Bosch MIC SERIES 500 CAMERA 500 User Manual Page 24

Comments to this Manuals

Related products and manuals for Security cameras Bosch MIC SERIES 500 CAMERA 500